Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

304 Austenitic Stainless Steel (18/8) — 2 mm 3-Flute Speeds & Feeds

ISO Group M 180 HB / 88 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
22,282 RPM
Surface Speed: 140 m/min (459.3 SFM)
Table Feed Rate F = RPM·z·fz
541 mm/min
21.4 IPM
Plunge/Ramp Rate: 189 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0081 mm/t
0.00032 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
0.81 cm³/min
0.05 in³/min
Power Required: 0.04 kW (0.05 HP)
Direct CNC Machining Solution

For milling 304 Austenitic Stainless Steel (18/8) with a 2 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 22,282 RPM at 140 m/min (459.3 SFM), with a profiling feed rate of 541 mm/min (21.4 IPM) and adjusted chip load of 0.0081 mm/tooth, achieving a material removal rate of 0.81 cm³/min (0.05 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
304 Austenitic Stainless Steel (18/8) Stock CLIMB D = 2 mm (0.0787") ae = 0.5 mm ap = 3 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.01 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (140 × 1000) / (π × 2) = 22,282 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.5/2 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.007 mm × 1.1547 = 0.0081 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 22,282 × 3 × 0.0081 = 541 mm/min (21.4 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (3 × 0.5 × 541) / 1000 = 0.81 cm³/min (0.05 in³/min)
Specific Cutting Force (kc) for 304 Austenitic Stainless Steel (18/8): 2200 N/mm². Spindle drive efficiency η = 0.80.

304 Austenitic Stainless Steel (18/8) (2 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 2 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 2 mm 1 mm 1× 232 8.9 0.46 0.02
Slotting (100% WOC) 3F 2 mm 1 mm 1× 348 13.4 0.7 0.03
Slotting (100% WOC) 4F 2 mm 1 mm 1× 463 17.8 0.93 0.04
Profiling / HEM (25% WOC) 2F 0.5 mm 3 mm 1.1547× 361 14.3 0.54 0.02
Profiling / HEM (25% WOC) CURRENT 3F 0.5 mm 3 mm 1.1547× 541 21.4 0.81 0.04
Profiling / HEM (25% WOC) 4F 0.5 mm 3 mm 1.1547× 722 28.5 1.08 0.05
Adaptive Clearing (10% WOC) 2F 0.2 mm 4 mm 1.6667× 521 20.5 0.42 0.02
Adaptive Clearing (10% WOC) 3F 0.2 mm 4 mm 1.6667× 782 30.7 0.63 0.03
Adaptive Clearing (10% WOC) 4F 0.2 mm 4 mm 1.6667× 1,043 41 0.83 0.04

Shop-Floor Machining Strategy for 304 Austenitic Stainless Steel (18/8)

Work Hardening: EXTREME
Coolant & Lubrication Protocol

High-Pressure Flood Coolant (10-12% Oil Concentration)

Pressure: 20 to 70 bar through-spindle preferred

Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.

Chip Evacuation & Tool Path Guidance

Chip Flow: Tough, stringy, work-hardened chips. Chip clearance is paramount.

Milling Direction: MANDATORY climb milling. Conventional milling rubs before shearing and work-hardens the surface to 45+ HRC.

Expert Machinist Tips:
  • NEVER DWELL OR RUB: Maintain positive feed per tooth at all times. If the cutter rubs, the workpiece work-hardens instantly.
  • Use unequal helix angle (variable helix) 4-flute end mills to damp out chatter harmonics.
  • AlTiN or multi-layer nano-coatings provide critical barrier against built-up edge and notch wear.

Frequently Asked CNC Questions (304 Austenitic Stainless Steel (18/8) / 2 mm)

What is the recommended RPM for milling 304 Austenitic Stainless Steel (18/8) with a 2 mm end mill?
For a 2 mm (2 mm) TiAlN coated carbide end mill in 304 Austenitic Stainless Steel (18/8), the baseline surface cutting speed is 140 m/min (459.3 SFM), which translates to a calculated spindle speed of 22,282 RPM. If using uncoated carbide, reduce surface speed to 115 m/min (380 SFM / 18303 RPM). For HSS cutters, speed must be restricted to 20 m/min (3183 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 2 mm in 304 Austenitic Stainless Steel (18/8)?
At 22,282 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0081 mm/tooth (0.00032"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 541 mm/min (21.4 IPM). Ramping or plunging into material should be limited to 35% of table feed (189 mm/min / 7.5 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.5 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 304 Austenitic Stainless Steel (18/8)?
High-Pressure Flood Coolant (10-12% Oil Concentration). Pressure specification: 20 to 70 bar through-spindle preferred. Engineering rationale: Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.