Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

304 Austenitic Stainless Steel (18/8) — 8 mm 4-Flute Speeds & Feeds

ISO Group M 180 HB / 88 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
5,570 RPM
Surface Speed: 140 m/min (459.3 SFM)
Table Feed Rate F = RPM·z·fz
544 mm/min
21.4 IPM
Plunge/Ramp Rate: 190 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0244 mm/t
0.00096 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
13.06 cm³/min
0.8 in³/min
Power Required: 0.6 kW (0.8 HP)
Direct CNC Machining Solution

For milling 304 Austenitic Stainless Steel (18/8) with a 8 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 5,570 RPM at 140 m/min (459.3 SFM), with a profiling feed rate of 544 mm/min (21.4 IPM) and adjusted chip load of 0.0244 mm/tooth, achieving a material removal rate of 13.06 cm³/min (0.8 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
304 Austenitic Stainless Steel (18/8) Stock CLIMB D = 8 mm (0.315") ae = 2 mm ap = 12 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.82 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (140 × 1000) / (π × 8) = 5,570 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 2/8 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0211 mm × 1.1547 = 0.0244 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 5,570 × 4 × 0.0244 = 544 mm/min (21.4 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (12 × 2 × 544) / 1000 = 13.06 cm³/min (0.8 in³/min)
Specific Cutting Force (kc) for 304 Austenitic Stainless Steel (18/8): 2200 N/mm². Spindle drive efficiency η = 0.80.

304 Austenitic Stainless Steel (18/8) (8 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 8 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 8 mm 4 mm 1× 176 6.9 5.63 0.26
Slotting (100% WOC) 3F 8 mm 4 mm 1× 264 10.4 8.45 0.39
Slotting (100% WOC) 4F 8 mm 4 mm 1× 352 13.8 11.26 0.52
Profiling / HEM (25% WOC) 2F 2 mm 12 mm 1.1547× 272 10.7 6.53 0.3
Profiling / HEM (25% WOC) 3F 2 mm 12 mm 1.1547× 408 16 9.79 0.45
Profiling / HEM (25% WOC) CURRENT 4F 2 mm 12 mm 1.1547× 544 21.4 13.06 0.6
Adaptive Clearing (10% WOC) 2F 0.8 mm 16 mm 1.6667× 392 15.5 5.02 0.23
Adaptive Clearing (10% WOC) 3F 0.8 mm 16 mm 1.6667× 588 23.2 7.53 0.35
Adaptive Clearing (10% WOC) 4F 0.8 mm 16 mm 1.6667× 784 31 10.04 0.46

Shop-Floor Machining Strategy for 304 Austenitic Stainless Steel (18/8)

Work Hardening: EXTREME
Coolant & Lubrication Protocol

High-Pressure Flood Coolant (10-12% Oil Concentration)

Pressure: 20 to 70 bar through-spindle preferred

Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.

Chip Evacuation & Tool Path Guidance

Chip Flow: Tough, stringy, work-hardened chips. Chip clearance is paramount.

Milling Direction: MANDATORY climb milling. Conventional milling rubs before shearing and work-hardens the surface to 45+ HRC.

Expert Machinist Tips:
  • NEVER DWELL OR RUB: Maintain positive feed per tooth at all times. If the cutter rubs, the workpiece work-hardens instantly.
  • Use unequal helix angle (variable helix) 4-flute end mills to damp out chatter harmonics.
  • AlTiN or multi-layer nano-coatings provide critical barrier against built-up edge and notch wear.

Frequently Asked CNC Questions (304 Austenitic Stainless Steel (18/8) / 8 mm)

What is the recommended RPM for milling 304 Austenitic Stainless Steel (18/8) with a 8 mm end mill?
For a 8 mm (8 mm) TiAlN coated carbide end mill in 304 Austenitic Stainless Steel (18/8), the baseline surface cutting speed is 140 m/min (459.3 SFM), which translates to a calculated spindle speed of 5,570 RPM. If using uncoated carbide, reduce surface speed to 115 m/min (380 SFM / 4576 RPM). For HSS cutters, speed must be restricted to 20 m/min (796 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 8 mm in 304 Austenitic Stainless Steel (18/8)?
At 5,570 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0244 mm/tooth (0.00096"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 544 mm/min (21.4 IPM). Ramping or plunging into material should be limited to 35% of table feed (190 mm/min / 7.5 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 2 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 304 Austenitic Stainless Steel (18/8)?
High-Pressure Flood Coolant (10-12% Oil Concentration). Pressure specification: 20 to 70 bar through-spindle preferred. Engineering rationale: Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.