316 Marine Grade Stainless Steel (with Molybdenum) — 20 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 316 Marine Grade Stainless Steel (with Molybdenum) with a 20 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 1,989 RPM at 125 m/min (410.1 SFM), with a profiling feed rate of 192 mm/min (7.6 IPM) and adjusted chip load of 0.0482 mm/tooth, achieving a material removal rate of 28.8 cm³/min (1.77 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math316 Marine Grade Stainless Steel (with Molybdenum) (20 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 20 mm | 10 mm | 1× | 125 | 4.9 | 25 | 1.2 |
| Slotting (100% WOC) | 3F | 20 mm | 10 mm | 1× | 187 | 7.3 | 37.4 | 1.79 |
| Slotting (100% WOC) | 4F | 20 mm | 10 mm | 1× | 249 | 9.8 | 49.8 | 2.39 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 5 mm | 30 mm | 1.1547× | 192 | 7.6 | 28.8 | 1.38 |
| Profiling / HEM (25% WOC) | 3F | 5 mm | 30 mm | 1.1547× | 288 | 11.3 | 43.2 | 2.07 |
| Profiling / HEM (25% WOC) | 4F | 5 mm | 30 mm | 1.1547× | 383 | 15.1 | 57.45 | 2.75 |
| Adaptive Clearing (10% WOC) | 2F | 2 mm | 40 mm | 1.6667× | 276 | 10.9 | 22.08 | 1.06 |
| Adaptive Clearing (10% WOC) | 3F | 2 mm | 40 mm | 1.6667× | 415 | 16.3 | 33.2 | 1.59 |
| Adaptive Clearing (10% WOC) | 4F | 2 mm | 40 mm | 1.6667× | 553 | 21.8 | 44.24 | 2.12 |
Shop-Floor Machining Strategy for 316 Marine Grade Stainless Steel (with Molybdenum)
Work Hardening: EXTREMEHeavy Flood Coolant with Extreme Pressure (EP) Additives
Pressure: 20 bar minimum
Molybdenum addition increases chemical and high-temp shear toughness, requiring superior lubricity.
Chip Flow: High tendency for chips to weld to cutting edges if feed pauses.
Milling Direction: Mandatory climb milling.
- Reduce SFM by 10-15% compared to 304 stainless; keep chip load firm.
- Corner chamfer or radiused cutters prevent premature notch wear on the depth-of-cut line.
- Use high-feed milling or trochoidal toolpaths to spread wear along the full flute length.
Frequently Asked CNC Questions (316 Marine Grade Stainless Steel (with Molybdenum) / 20 mm)
What is the recommended RPM for milling 316 Marine Grade Stainless Steel (with Molybdenum) with a 20 mm end mill?
What table feed rate and chip load should I program for 20 mm in 316 Marine Grade Stainless Steel (with Molybdenum)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 316 Marine Grade Stainless Steel (with Molybdenum)?
Recent Calculations
No recent calculations saved yet.