6061-T6 Aluminum — 1/8" (0.125 in) 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 6061-T6 Aluminum with a 1/8" (0.125 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 65,166 RPM at 650 m/min (2132.5 SFM), with a profiling feed rate of 2,854 mm/min (112.1 IPM) and adjusted chip load of 0.0219 mm/tooth, achieving a material removal rate of 10.73 cm³/min (0.65 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math6061-T6 Aluminum (1/8" (0.125 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 3.17 mm | 1.59 mm | 1× | 1,851 | 73 | 9.33 | 0.14 |
| Slotting (100% WOC) | 3F | 3.17 mm | 1.59 mm | 1× | 2,776 | 109.5 | 13.99 | 0.2 |
| Slotting (100% WOC) | 4F | 3.17 mm | 1.59 mm | 1× | 3,701 | 146 | 18.65 | 0.27 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 0.79 mm | 4.76 mm | 1.1565× | 2,854 | 112.1 | 10.73 | 0.16 |
| Profiling / HEM (25% WOC) | 3F | 0.79 mm | 4.76 mm | 1.1565× | 4,281 | 168.1 | 16.1 | 0.23 |
| Profiling / HEM (25% WOC) | 4F | 0.79 mm | 4.76 mm | 1.1565× | 5,709 | 224.2 | 21.47 | 0.31 |
| Adaptive Clearing (10% WOC) | 2F | 0.32 mm | 6.35 mm | 1.6609× | 4,092 | 161.6 | 8.31 | 0.12 |
| Adaptive Clearing (10% WOC) | 3F | 0.32 mm | 6.35 mm | 1.6609× | 6,139 | 242.4 | 12.47 | 0.18 |
| Adaptive Clearing (10% WOC) | 4F | 0.32 mm | 6.35 mm | 1.6609× | 8,185 | 323.2 | 16.63 | 0.24 |
Shop-Floor Machining Strategy for 6061-T6 Aluminum
Work Hardening: LowHigh-Pressure Flood Coolant or MQL Air Blast with Alcohol/Oil Mist
Pressure: Flood at 5-10 bar; Through-Spindle 20 bar
Lubricity is critical. Dry cutting risks instantaneous aluminum welding to tool flutes and catastrophic cutter snap.
Chip Flow: Use polished flutes (ZrN or DLC coating) and 2 or 3 flutes to prevent chip re-cutting.
Milling Direction: Always climb mill. Conventional milling causes built-up edge on the tool face.
- Max spindle speed is usually preferred; feed fast to maintain minimum chip thickness (>0.02 mm) to prevent rubbing.
- In deep pocketing, utilize high pressure air blast to blast chips out of the cavity.
- For high-speed trochoidal slotting, use 10-15% radial stepover (ae) at 2.0x-3.0x axial depth (ap).
Frequently Asked CNC Questions (6061-T6 Aluminum / 1/8" (0.125 in))
What is the recommended RPM for milling 6061-T6 Aluminum with a 1/8" (0.125 in) end mill?
What table feed rate and chip load should I program for 1/8" (0.125 in) in 6061-T6 Aluminum?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 6061-T6 Aluminum?
Recent Calculations
No recent calculations saved yet.