6061-T6 Aluminum — 16 mm 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 6061-T6 Aluminum with a 16 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 12,931 RPM at 650 m/min (2132.5 SFM), with a profiling feed rate of 3,088 mm/min (121.4 IPM) and adjusted chip load of 0.0796 mm/tooth, achieving a material removal rate of 296.45 cm³/min (18.07 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math6061-T6 Aluminum (16 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 16 mm | 8 mm | 1× | 1,337 | 52.8 | 171.14 | 2.5 |
| Slotting (100% WOC) | 3F | 16 mm | 8 mm | 1× | 2,006 | 79.1 | 256.77 | 3.74 |
| Slotting (100% WOC) | 4F | 16 mm | 8 mm | 1× | 2,674 | 105.5 | 342.27 | 4.99 |
| Profiling / HEM (25% WOC) | 2F | 4 mm | 24 mm | 1.1547× | 2,059 | 80.9 | 197.66 | 2.88 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 4 mm | 24 mm | 1.1547× | 3,088 | 121.4 | 296.45 | 4.32 |
| Profiling / HEM (25% WOC) | 4F | 4 mm | 24 mm | 1.1547× | 4,117 | 161.9 | 395.23 | 5.76 |
| Adaptive Clearing (10% WOC) | 2F | 1.6 mm | 32 mm | 1.6667× | 2,969 | 116.9 | 152.01 | 2.22 |
| Adaptive Clearing (10% WOC) | 3F | 1.6 mm | 32 mm | 1.6667× | 4,453 | 175.3 | 227.99 | 3.32 |
| Adaptive Clearing (10% WOC) | 4F | 1.6 mm | 32 mm | 1.6667× | 5,938 | 233.8 | 304.03 | 4.43 |
Shop-Floor Machining Strategy for 6061-T6 Aluminum
Work Hardening: LowHigh-Pressure Flood Coolant or MQL Air Blast with Alcohol/Oil Mist
Pressure: Flood at 5-10 bar; Through-Spindle 20 bar
Lubricity is critical. Dry cutting risks instantaneous aluminum welding to tool flutes and catastrophic cutter snap.
Chip Flow: Use polished flutes (ZrN or DLC coating) and 2 or 3 flutes to prevent chip re-cutting.
Milling Direction: Always climb mill. Conventional milling causes built-up edge on the tool face.
- Max spindle speed is usually preferred; feed fast to maintain minimum chip thickness (>0.02 mm) to prevent rubbing.
- In deep pocketing, utilize high pressure air blast to blast chips out of the cavity.
- For high-speed trochoidal slotting, use 10-15% radial stepover (ae) at 2.0x-3.0x axial depth (ap).
Frequently Asked CNC Questions (6061-T6 Aluminum / 16 mm)
What is the recommended RPM for milling 6061-T6 Aluminum with a 16 mm end mill?
What table feed rate and chip load should I program for 16 mm in 6061-T6 Aluminum?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 6061-T6 Aluminum?
Recent Calculations
No recent calculations saved yet.