6061-T6 Aluminum — 4 mm 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 6061-T6 Aluminum with a 4 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 51,725 RPM at 650 m/min (2132.5 SFM), with a profiling feed rate of 4,066 mm/min (159.8 IPM) and adjusted chip load of 0.0262 mm/tooth, achieving a material removal rate of 24.4 cm³/min (1.49 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math6061-T6 Aluminum (4 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 4 mm | 2 mm | 1× | 1,769 | 69.3 | 14.15 | 0.21 |
| Slotting (100% WOC) | 3F | 4 mm | 2 mm | 1× | 2,653 | 104 | 21.22 | 0.31 |
| Slotting (100% WOC) | 4F | 4 mm | 2 mm | 1× | 3,538 | 138.6 | 28.3 | 0.41 |
| Profiling / HEM (25% WOC) | 2F | 1 mm | 6 mm | 1.1547× | 2,710 | 106.6 | 16.26 | 0.24 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 1 mm | 6 mm | 1.1547× | 4,066 | 159.8 | 24.4 | 0.36 |
| Profiling / HEM (25% WOC) | 4F | 1 mm | 6 mm | 1.1547× | 5,421 | 213.1 | 32.53 | 0.47 |
| Adaptive Clearing (10% WOC) | 2F | 0.4 mm | 8 mm | 1.6667× | 3,910 | 154.1 | 12.51 | 0.18 |
| Adaptive Clearing (10% WOC) | 3F | 0.4 mm | 8 mm | 1.6667× | 5,866 | 231.2 | 18.77 | 0.27 |
| Adaptive Clearing (10% WOC) | 4F | 0.4 mm | 8 mm | 1.6667× | 7,821 | 308.3 | 25.03 | 0.37 |
Shop-Floor Machining Strategy for 6061-T6 Aluminum
Work Hardening: LowHigh-Pressure Flood Coolant or MQL Air Blast with Alcohol/Oil Mist
Pressure: Flood at 5-10 bar; Through-Spindle 20 bar
Lubricity is critical. Dry cutting risks instantaneous aluminum welding to tool flutes and catastrophic cutter snap.
Chip Flow: Use polished flutes (ZrN or DLC coating) and 2 or 3 flutes to prevent chip re-cutting.
Milling Direction: Always climb mill. Conventional milling causes built-up edge on the tool face.
- Max spindle speed is usually preferred; feed fast to maintain minimum chip thickness (>0.02 mm) to prevent rubbing.
- In deep pocketing, utilize high pressure air blast to blast chips out of the cavity.
- For high-speed trochoidal slotting, use 10-15% radial stepover (ae) at 2.0x-3.0x axial depth (ap).
Frequently Asked CNC Questions (6061-T6 Aluminum / 4 mm)
What is the recommended RPM for milling 6061-T6 Aluminum with a 4 mm end mill?
What table feed rate and chip load should I program for 4 mm in 6061-T6 Aluminum?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 6061-T6 Aluminum?
Recent Calculations
No recent calculations saved yet.