6061-T6 Aluminum — 6 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 6061-T6 Aluminum with a 6 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 34,484 RPM at 650 m/min (2132.5 SFM), with a profiling feed rate of 2,504 mm/min (98.6 IPM) and adjusted chip load of 0.0363 mm/tooth, achieving a material removal rate of 33.8 cm³/min (2.06 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math6061-T6 Aluminum (6 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6 mm | 3 mm | 1× | 1,628 | 64.1 | 29.3 | 0.43 |
| Slotting (100% WOC) | 3F | 6 mm | 3 mm | 1× | 2,441 | 96.2 | 43.94 | 0.64 |
| Slotting (100% WOC) | 4F | 6 mm | 3 mm | 1× | 3,255 | 128.3 | 58.59 | 0.85 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 1.5 mm | 9 mm | 1.1547× | 2,504 | 98.6 | 33.8 | 0.49 |
| Profiling / HEM (25% WOC) | 3F | 1.5 mm | 9 mm | 1.1547× | 3,755 | 147.9 | 50.69 | 0.74 |
| Profiling / HEM (25% WOC) | 4F | 1.5 mm | 9 mm | 1.1547× | 5,007 | 197.2 | 67.59 | 0.99 |
| Adaptive Clearing (10% WOC) | 2F | 0.6 mm | 12 mm | 1.6667× | 3,607 | 142.1 | 25.97 | 0.38 |
| Adaptive Clearing (10% WOC) | 3F | 0.6 mm | 12 mm | 1.6667× | 5,411 | 213.1 | 38.96 | 0.57 |
| Adaptive Clearing (10% WOC) | 4F | 0.6 mm | 12 mm | 1.6667× | 7,214 | 284.1 | 51.94 | 0.76 |
Shop-Floor Machining Strategy for 6061-T6 Aluminum
Work Hardening: LowHigh-Pressure Flood Coolant or MQL Air Blast with Alcohol/Oil Mist
Pressure: Flood at 5-10 bar; Through-Spindle 20 bar
Lubricity is critical. Dry cutting risks instantaneous aluminum welding to tool flutes and catastrophic cutter snap.
Chip Flow: Use polished flutes (ZrN or DLC coating) and 2 or 3 flutes to prevent chip re-cutting.
Milling Direction: Always climb mill. Conventional milling causes built-up edge on the tool face.
- Max spindle speed is usually preferred; feed fast to maintain minimum chip thickness (>0.02 mm) to prevent rubbing.
- In deep pocketing, utilize high pressure air blast to blast chips out of the cavity.
- For high-speed trochoidal slotting, use 10-15% radial stepover (ae) at 2.0x-3.0x axial depth (ap).
Frequently Asked CNC Questions (6061-T6 Aluminum / 6 mm)
What is the recommended RPM for milling 6061-T6 Aluminum with a 6 mm end mill?
What table feed rate and chip load should I program for 6 mm in 6061-T6 Aluminum?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 6061-T6 Aluminum?
Recent Calculations
No recent calculations saved yet.