C11000 Electrolytic Tough Pitch (ETP) Copper — 1" (1.000 in) 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 1" (1.000 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 3,133 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 434 mm/min (17 IPM) and adjusted chip load of 0.0692 mm/tooth, achieving a material removal rate of 105 cm³/min (6.38 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathC11000 Electrolytic Tough Pitch (ETP) Copper (1" (1.000 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 25.4 mm | 12.7 mm | 1× | 281 | 11.1 | 90.64 | 2.08 |
| Slotting (100% WOC) | 3F | 25.4 mm | 12.7 mm | 1× | 422 | 16.6 | 136.13 | 3.12 |
| Slotting (100% WOC) | 4F | 25.4 mm | 12.7 mm | 1× | 563 | 22.2 | 181.61 | 4.16 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 6.35 mm | 38.1 mm | 1.1547× | 434 | 17 | 105 | 2.41 |
| Profiling / HEM (25% WOC) | 3F | 6.35 mm | 38.1 mm | 1.1547× | 650 | 25.6 | 157.26 | 3.6 |
| Profiling / HEM (25% WOC) | 4F | 6.35 mm | 38.1 mm | 1.1547× | 867 | 34.1 | 209.76 | 4.81 |
| Adaptive Clearing (10% WOC) | 2F | 2.54 mm | 50.8 mm | 1.6667× | 625 | 24.6 | 80.64 | 1.85 |
| Adaptive Clearing (10% WOC) | 3F | 2.54 mm | 50.8 mm | 1.6667× | 938 | 36.9 | 121.03 | 2.77 |
| Adaptive Clearing (10% WOC) | 4F | 2.54 mm | 50.8 mm | 1.6667× | 1,251 | 49.3 | 161.42 | 3.7 |
Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper
Work Hardening: ModerateAbundant Flood Coolant with High Lubricity Emulsion or Mineral Oil
Pressure: Flood at 8 bar minimum
Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.
Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.
Milling Direction: Climb milling with high positive rake angles.
- Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
- Keep feed rate positive to shear rather than plow or smear the copper grain structure.
- Program chamfering passes immediately following roughing before secondary operations.
Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 1" (1.000 in))
What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 1" (1.000 in) end mill?
What table feed rate and chip load should I program for 1" (1.000 in) in C11000 Electrolytic Tough Pitch (ETP) Copper?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Recent Calculations
No recent calculations saved yet.