C11000 Electrolytic Tough Pitch (ETP) Copper — 10 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 10 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 7,958 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 1,044 mm/min (41.1 IPM) and adjusted chip load of 0.0328 mm/tooth, achieving a material removal rate of 39.15 cm³/min (2.39 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathC11000 Electrolytic Tough Pitch (ETP) Copper (10 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 10 mm | 5 mm | 1× | 339 | 13.4 | 16.95 | 0.39 |
| Slotting (100% WOC) | 3F | 10 mm | 5 mm | 1× | 509 | 20.1 | 25.45 | 0.58 |
| Slotting (100% WOC) | 4F | 10 mm | 5 mm | 1× | 678 | 26.7 | 33.9 | 0.78 |
| Profiling / HEM (25% WOC) | 2F | 2.5 mm | 15 mm | 1.1547× | 522 | 20.5 | 19.57 | 0.45 |
| Profiling / HEM (25% WOC) | 3F | 2.5 mm | 15 mm | 1.1547× | 783 | 30.8 | 29.36 | 0.67 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 2.5 mm | 15 mm | 1.1547× | 1,044 | 41.1 | 39.15 | 0.9 |
| Adaptive Clearing (10% WOC) | 2F | 1 mm | 20 mm | 1.6667× | 753 | 29.6 | 15.06 | 0.35 |
| Adaptive Clearing (10% WOC) | 3F | 1 mm | 20 mm | 1.6667× | 1,129 | 44.4 | 22.58 | 0.52 |
| Adaptive Clearing (10% WOC) | 4F | 1 mm | 20 mm | 1.6667× | 1,506 | 59.2 | 30.12 | 0.69 |
Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper
Work Hardening: ModerateAbundant Flood Coolant with High Lubricity Emulsion or Mineral Oil
Pressure: Flood at 8 bar minimum
Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.
Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.
Milling Direction: Climb milling with high positive rake angles.
- Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
- Keep feed rate positive to shear rather than plow or smear the copper grain structure.
- Program chamfering passes immediately following roughing before secondary operations.
Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 10 mm)
What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 10 mm end mill?
What table feed rate and chip load should I program for 10 mm in C11000 Electrolytic Tough Pitch (ETP) Copper?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Recent Calculations
No recent calculations saved yet.