Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

C11000 Electrolytic Tough Pitch (ETP) Copper — 3/16" (0.1875 in) 2-Flute Speeds & Feeds

ISO Group N 50 HB / 40 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
16,711 RPM
Surface Speed: 250 m/min (820.2 SFM)
Table Feed Rate F = RPM·z·fz
605 mm/min
23.7 IPM
Plunge/Ramp Rate: 212 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0181 mm/t
0.00071 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
5.14 cm³/min
0.31 in³/min
Power Required: 0.12 kW (0.16 HP)
Direct CNC Machining Solution

For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 3/16" (0.1875 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 16,711 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 605 mm/min (23.7 IPM) and adjusted chip load of 0.0181 mm/tooth, achieving a material removal rate of 5.14 cm³/min (0.31 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
C11000 Electrolytic Tough Pitch (ETP) Copper Stock CLIMB D = 4.762 mm (0.1875") ae = 1.19 mm ap = 7.14 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 0.05 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (250 × 1000) / (π × 4.762) = 16,711 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1.19/4.762 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0157 mm × 1.1549 = 0.0181 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 16,711 × 2 × 0.0181 = 605 mm/min (23.7 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (7.14 × 1.19 × 605) / 1000 = 5.14 cm³/min (0.31 in³/min)
Specific Cutting Force (kc) for C11000 Electrolytic Tough Pitch (ETP) Copper: 1100 N/mm². Spindle drive efficiency η = 0.80.

C11000 Electrolytic Tough Pitch (ETP) Copper (3/16" (0.1875 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/16" (0.1875 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 4.76 mm 2.38 mm 1× 394 15.4 4.46 0.1
Slotting (100% WOC) 3F 4.76 mm 2.38 mm 1× 592 23.1 6.71 0.15
Slotting (100% WOC) 4F 4.76 mm 2.38 mm 1× 789 30.7 8.94 0.2
Profiling / HEM (25% WOC) CURRENT 2F 1.19 mm 7.14 mm 1.1549× 605 23.7 5.14 0.12
Profiling / HEM (25% WOC) 3F 1.19 mm 7.14 mm 1.1549× 907 35.6 7.71 0.18
Profiling / HEM (25% WOC) 4F 1.19 mm 7.14 mm 1.1549× 1,210 47.5 10.28 0.24
Adaptive Clearing (10% WOC) 2F 0.48 mm 9.52 mm 1.6608× 872 34.4 3.98 0.09
Adaptive Clearing (10% WOC) 3F 0.48 mm 9.52 mm 1.6608× 1,308 51.6 5.98 0.14
Adaptive Clearing (10% WOC) 4F 0.48 mm 9.52 mm 1.6608× 1,745 68.8 7.97 0.18

Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper

Work Hardening: Moderate
Coolant & Lubrication Protocol

Abundant Flood Coolant with High Lubricity Emulsion or Mineral Oil

Pressure: Flood at 8 bar minimum

Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.

Chip Evacuation & Tool Path Guidance

Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.

Milling Direction: Climb milling with high positive rake angles.

Expert Machinist Tips:
  • Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
  • Keep feed rate positive to shear rather than plow or smear the copper grain structure.
  • Program chamfering passes immediately following roughing before secondary operations.

Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 3/16" (0.1875 in))

What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 3/16" (0.1875 in) end mill?
For a 3/16" (0.1875 in) (4.762 mm) TiAlN coated carbide end mill in C11000 Electrolytic Tough Pitch (ETP) Copper, the baseline surface cutting speed is 250 m/min (820.2 SFM), which translates to a calculated spindle speed of 16,711 RPM. If using uncoated carbide, reduce surface speed to 200 m/min (650 SFM / 13369 RPM). For HSS cutters, speed must be restricted to 45 m/min (3008 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/16" (0.1875 in) in C11000 Electrolytic Tough Pitch (ETP) Copper?
At 16,711 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0181 mm/tooth (0.00071"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 605 mm/min (23.7 IPM). Ramping or plunging into material should be limited to 35% of table feed (212 mm/min / 8.3 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1.19 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Abundant Flood Coolant with High Lubricity Emulsion or Mineral Oil. Pressure specification: Flood at 8 bar minimum. Engineering rationale: Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.