C11000 Electrolytic Tough Pitch (ETP) Copper — 3 mm 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 3 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 26,526 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 995 mm/min (39 IPM) and adjusted chip load of 0.0125 mm/tooth, achieving a material removal rate of 3.36 cm³/min (0.2 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathC11000 Electrolytic Tough Pitch (ETP) Copper (3 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 3 mm | 1.5 mm | 1× | 430 | 17 | 1.94 | 0.04 |
| Slotting (100% WOC) | 3F | 3 mm | 1.5 mm | 1× | 645 | 25.5 | 2.9 | 0.07 |
| Slotting (100% WOC) | 4F | 3 mm | 1.5 mm | 1× | 859 | 34 | 3.87 | 0.09 |
| Profiling / HEM (25% WOC) | 2F | 0.75 mm | 4.5 mm | 1.1547× | 663 | 26 | 2.24 | 0.05 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 0.75 mm | 4.5 mm | 1.1547× | 995 | 39 | 3.36 | 0.08 |
| Profiling / HEM (25% WOC) | 4F | 0.75 mm | 4.5 mm | 1.1547× | 1,326 | 52 | 4.48 | 0.1 |
| Adaptive Clearing (10% WOC) | 2F | 0.3 mm | 6 mm | 1.6667× | 955 | 37.7 | 1.72 | 0.04 |
| Adaptive Clearing (10% WOC) | 3F | 0.3 mm | 6 mm | 1.6667× | 1,432 | 56.5 | 2.58 | 0.06 |
| Adaptive Clearing (10% WOC) | 4F | 0.3 mm | 6 mm | 1.6667× | 1,910 | 75.3 | 3.44 | 0.08 |
Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper
Work Hardening: ModerateAbundant Flood Coolant with High Lubricity Emulsion or Mineral Oil
Pressure: Flood at 8 bar minimum
Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.
Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.
Milling Direction: Climb milling with high positive rake angles.
- Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
- Keep feed rate positive to shear rather than plow or smear the copper grain structure.
- Program chamfering passes immediately following roughing before secondary operations.
Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 3 mm)
What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 3 mm end mill?
What table feed rate and chip load should I program for 3 mm in C11000 Electrolytic Tough Pitch (ETP) Copper?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Recent Calculations
No recent calculations saved yet.