C11000 Electrolytic Tough Pitch (ETP) Copper — 8 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 8 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 9,947 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 547 mm/min (21.5 IPM) and adjusted chip load of 0.0275 mm/tooth, achieving a material removal rate of 13.13 cm³/min (0.8 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathC11000 Electrolytic Tough Pitch (ETP) Copper (8 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 8 mm | 4 mm | 1× | 354 | 13.9 | 11.33 | 0.26 |
| Slotting (100% WOC) | 3F | 8 mm | 4 mm | 1× | 531 | 20.9 | 16.99 | 0.39 |
| Slotting (100% WOC) | 4F | 8 mm | 4 mm | 1× | 708 | 27.9 | 22.66 | 0.52 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 2 mm | 12 mm | 1.1547× | 547 | 21.5 | 13.13 | 0.3 |
| Profiling / HEM (25% WOC) | 3F | 2 mm | 12 mm | 1.1547× | 821 | 32.2 | 19.7 | 0.45 |
| Profiling / HEM (25% WOC) | 4F | 2 mm | 12 mm | 1.1547× | 1,094 | 43 | 26.26 | 0.6 |
| Adaptive Clearing (10% WOC) | 2F | 0.8 mm | 16 mm | 1.6667× | 790 | 31 | 10.11 | 0.23 |
| Adaptive Clearing (10% WOC) | 3F | 0.8 mm | 16 mm | 1.6667× | 1,185 | 46.6 | 15.17 | 0.35 |
| Adaptive Clearing (10% WOC) | 4F | 0.8 mm | 16 mm | 1.6667× | 1,580 | 62.1 | 20.22 | 0.46 |
Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper
Work Hardening: ModerateAbundant Flood Coolant with High Lubricity Emulsion or Mineral Oil
Pressure: Flood at 8 bar minimum
Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.
Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.
Milling Direction: Climb milling with high positive rake angles.
- Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
- Keep feed rate positive to shear rather than plow or smear the copper grain structure.
- Program chamfering passes immediately following roughing before secondary operations.
Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 8 mm)
What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 8 mm end mill?
What table feed rate and chip load should I program for 8 mm in C11000 Electrolytic Tough Pitch (ETP) Copper?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Recent Calculations
No recent calculations saved yet.