Delrin (Acetal / Polyoxymethylene / POM-C) — 20 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 20 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 7,958 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 1,716 mm/min (67.5 IPM) and adjusted chip load of 0.1078 mm/tooth, achieving a material removal rate of 257.4 cm³/min (15.7 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathDelrin (Acetal / Polyoxymethylene / POM-C) (20 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 20 mm | 10 mm | 1× | 1,114 | 43.9 | 222.8 | 1.16 |
| Slotting (100% WOC) | 3F | 20 mm | 10 mm | 1× | 1,671 | 65.9 | 334.2 | 1.74 |
| Slotting (100% WOC) | 4F | 20 mm | 10 mm | 1× | 2,228 | 87.9 | 445.6 | 2.32 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 5 mm | 30 mm | 1.1547× | 1,716 | 67.5 | 257.4 | 1.34 |
| Profiling / HEM (25% WOC) | 3F | 5 mm | 30 mm | 1.1547× | 2,574 | 101.2 | 386.1 | 2.01 |
| Profiling / HEM (25% WOC) | 4F | 5 mm | 30 mm | 1.1547× | 3,431 | 135 | 514.65 | 2.68 |
| Adaptive Clearing (10% WOC) | 2F | 2 mm | 40 mm | 1.6667× | 2,478 | 97.6 | 198.24 | 1.03 |
| Adaptive Clearing (10% WOC) | 3F | 2 mm | 40 mm | 1.6667× | 3,717 | 146.3 | 297.36 | 1.55 |
| Adaptive Clearing (10% WOC) | 4F | 2 mm | 40 mm | 1.6667× | 4,956 | 195.1 | 396.48 | 2.06 |
Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)
Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant
Pressure: Air gun at 5 bar
Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.
Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.
Milling Direction: Climb milling produces pristine finishes.
- High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
- Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
- Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.
Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 20 mm)
What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 20 mm end mill?
What table feed rate and chip load should I program for 20 mm in Delrin (Acetal / Polyoxymethylene / POM-C)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Recent Calculations
No recent calculations saved yet.