HDPE (High-Density Polyethylene) — 1/8" (0.125 in) 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling HDPE (High-Density Polyethylene) with a 1/8" (0.125 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 45,115 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 4,746 mm/min (187.7 IPM) and adjusted chip load of 0.0263 mm/tooth, achieving a material removal rate of 17.85 cm³/min (1.09 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathHDPE (High-Density Polyethylene) (1/8" (0.125 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 3.17 mm | 1.59 mm | 1× | 1,534 | 60.5 | 7.73 | 0.03 |
| Slotting (100% WOC) | 3F | 3.17 mm | 1.59 mm | 1× | 2,301 | 90.7 | 11.6 | 0.04 |
| Slotting (100% WOC) | 4F | 3.17 mm | 1.59 mm | 1× | 3,068 | 120.9 | 15.46 | 0.06 |
| Profiling / HEM (25% WOC) | 2F | 0.79 mm | 4.76 mm | 1.1565× | 2,373 | 93.8 | 8.92 | 0.03 |
| Profiling / HEM (25% WOC) | 3F | 0.79 mm | 4.76 mm | 1.1565× | 3,560 | 140.8 | 13.39 | 0.05 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 0.79 mm | 4.76 mm | 1.1565× | 4,746 | 187.7 | 17.85 | 0.07 |
| Adaptive Clearing (10% WOC) | 2F | 0.32 mm | 6.35 mm | 1.6609× | 3,402 | 133.5 | 6.91 | 0.03 |
| Adaptive Clearing (10% WOC) | 3F | 0.32 mm | 6.35 mm | 1.6609× | 5,103 | 200.3 | 10.37 | 0.04 |
| Adaptive Clearing (10% WOC) | 4F | 0.32 mm | 6.35 mm | 1.6609× | 6,803 | 267.1 | 13.82 | 0.05 |
Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)
Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)Cold Compressed Air Blast or Water Mist
Pressure: 5 bar compressed air
HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.
Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.
Milling Direction: Climb milling prevents feathered edge tears.
- Use razor-sharp single flute O-flute cutters with polished gullets.
- Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
- Do not allow tool to dwell or friction will melt a pocket into the plastic.
Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 1/8" (0.125 in))
What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 1/8" (0.125 in) end mill?
What table feed rate and chip load should I program for 1/8" (0.125 in) in HDPE (High-Density Polyethylene)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Recent Calculations
No recent calculations saved yet.