Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

Polycarbonate (Lexan / PC Thermoplastic) — 10 mm 3-Flute Speeds & Feeds

ISO Group O 70 Shore D / 118 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
12,096 RPM
Surface Speed: 380 m/min (1246.7 SFM)
Table Feed Rate F = RPM·z·fz
1,981 mm/min
78 IPM
Plunge/Ramp Rate: 693 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0546 mm/t
0.00215 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
74.29 cm³/min
4.53 in³/min
Power Required: 0.46 kW (0.62 HP)
Direct CNC Machining Solution

For milling Polycarbonate (Lexan / PC Thermoplastic) with a 10 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 12,096 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 1,981 mm/min (78 IPM) and adjusted chip load of 0.0546 mm/tooth, achieving a material removal rate of 74.29 cm³/min (4.53 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
Polycarbonate (Lexan / PC Thermoplastic) Stock CLIMB D = 10 mm (0.3937") ae = 2.5 mm ap = 15 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.29 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (380 × 1000) / (π × 10) = 12,096 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 2.5/10 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0473 mm × 1.1547 = 0.0546 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 12,096 × 3 × 0.0546 = 1,981 mm/min (78 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (15 × 2.5 × 1981) / 1000 = 74.29 cm³/min (4.53 in³/min)
Specific Cutting Force (kc) for Polycarbonate (Lexan / PC Thermoplastic): 300 N/mm². Spindle drive efficiency η = 0.80.

Polycarbonate (Lexan / PC Thermoplastic) (10 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 10 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 10 mm 5 mm 1× 859 33.9 42.95 0.27
Slotting (100% WOC) 3F 10 mm 5 mm 1× 1,288 50.8 64.4 0.4
Slotting (100% WOC) 4F 10 mm 5 mm 1× 1,718 67.7 85.9 0.54
Profiling / HEM (25% WOC) 2F 2.5 mm 15 mm 1.1547× 1,321 52 49.54 0.31
Profiling / HEM (25% WOC) CURRENT 3F 2.5 mm 15 mm 1.1547× 1,981 78 74.29 0.46
Profiling / HEM (25% WOC) 4F 2.5 mm 15 mm 1.1547× 2,642 104 99.08 0.62
Adaptive Clearing (10% WOC) 2F 1 mm 20 mm 1.6667× 1,906 75 38.12 0.24
Adaptive Clearing (10% WOC) 3F 1 mm 20 mm 1.6667× 2,859 112.5 57.18 0.36
Adaptive Clearing (10% WOC) 4F 1 mm 20 mm 1.6667× 3,813 150 76.26 0.48

Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)

Work Hardening: None (High internal residual stress from extrusion)
Coolant & Lubrication Protocol

Cold Air Blast Only or Pure Deionized Water

Pressure: Cold air gun at 5 bar

CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.

Chip Evacuation & Tool Path Guidance

Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.

Milling Direction: Climb milling mandatory to avoid chipping edge breakout.

Expert Machinist Tips:
  • Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
  • Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
  • Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.

Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 10 mm)

What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 10 mm end mill?
For a 10 mm (10 mm) TiAlN coated carbide end mill in Polycarbonate (Lexan / PC Thermoplastic), the baseline surface cutting speed is 380 m/min (1246.7 SFM), which translates to a calculated spindle speed of 12,096 RPM. If using uncoated carbide, reduce surface speed to 320 m/min (1050 SFM / 10186 RPM). For HSS cutters, speed must be restricted to 100 m/min (3183 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 10 mm in Polycarbonate (Lexan / PC Thermoplastic)?
At 12,096 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0546 mm/tooth (0.00215"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 1981 mm/min (78 IPM). Ramping or plunging into material should be limited to 35% of table feed (693 mm/min / 27.3 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 2.5 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Cold Air Blast Only or Pure Deionized Water. Pressure specification: Cold air gun at 5 bar. Engineering rationale: CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.