Polycarbonate (Lexan / PC Thermoplastic) — 20 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Polycarbonate (Lexan / PC Thermoplastic) with a 20 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 6,048 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 1,150 mm/min (45.2 IPM) and adjusted chip load of 0.0951 mm/tooth, achieving a material removal rate of 172.5 cm³/min (10.51 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathPolycarbonate (Lexan / PC Thermoplastic) (20 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 20 mm | 10 mm | 1× | 748 | 29.4 | 149.6 | 0.93 |
| Slotting (100% WOC) | 3F | 20 mm | 10 mm | 1× | 1,121 | 44.1 | 224.2 | 1.4 |
| Slotting (100% WOC) | 4F | 20 mm | 10 mm | 1× | 1,495 | 58.8 | 299 | 1.87 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 5 mm | 30 mm | 1.1547× | 1,150 | 45.2 | 172.5 | 1.08 |
| Profiling / HEM (25% WOC) | 3F | 5 mm | 30 mm | 1.1547× | 1,725 | 67.9 | 258.75 | 1.62 |
| Profiling / HEM (25% WOC) | 4F | 5 mm | 30 mm | 1.1547× | 2,301 | 90.5 | 345.15 | 2.16 |
| Adaptive Clearing (10% WOC) | 2F | 2 mm | 40 mm | 1.6667× | 1,661 | 65.4 | 132.88 | 0.83 |
| Adaptive Clearing (10% WOC) | 3F | 2 mm | 40 mm | 1.6667× | 2,491 | 98.2 | 199.28 | 1.25 |
| Adaptive Clearing (10% WOC) | 4F | 2 mm | 40 mm | 1.6667× | 3,322 | 130.9 | 265.76 | 1.66 |
Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)
Work Hardening: None (High internal residual stress from extrusion)Cold Air Blast Only or Pure Deionized Water
Pressure: Cold air gun at 5 bar
CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.
Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.
Milling Direction: Climb milling mandatory to avoid chipping edge breakout.
- Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
- Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
- Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.
Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 20 mm)
What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 20 mm end mill?
What table feed rate and chip load should I program for 20 mm in Polycarbonate (Lexan / PC Thermoplastic)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Recent Calculations
No recent calculations saved yet.