Polycarbonate (Lexan / PC Thermoplastic) — 2 mm 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Polycarbonate (Lexan / PC Thermoplastic) with a 2 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 60,479 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 2,740 mm/min (107 IPM) and adjusted chip load of 0.0151 mm/tooth, achieving a material removal rate of 4.11 cm³/min (0.25 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathPolycarbonate (Lexan / PC Thermoplastic) (2 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 2 mm | 1 mm | 1× | 1,185 | 47.2 | 2.37 | 0.01 |
| Slotting (100% WOC) | 3F | 2 mm | 1 mm | 1× | 1,778 | 70.8 | 3.56 | 0.02 |
| Slotting (100% WOC) | 4F | 2 mm | 1 mm | 1× | 2,371 | 94.3 | 4.74 | 0.03 |
| Profiling / HEM (25% WOC) | 2F | 0.5 mm | 3 mm | 1.1547× | 1,826 | 71.4 | 2.74 | 0.02 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 0.5 mm | 3 mm | 1.1547× | 2,740 | 107 | 4.11 | 0.03 |
| Profiling / HEM (25% WOC) | 4F | 0.5 mm | 3 mm | 1.1547× | 3,653 | 142.7 | 5.48 | 0.03 |
| Adaptive Clearing (10% WOC) | 2F | 0.2 mm | 4 mm | 1.6667× | 2,637 | 104 | 2.11 | 0.01 |
| Adaptive Clearing (10% WOC) | 3F | 0.2 mm | 4 mm | 1.6667× | 3,955 | 156 | 3.16 | 0.02 |
| Adaptive Clearing (10% WOC) | 4F | 0.2 mm | 4 mm | 1.6667× | 5,274 | 208 | 4.22 | 0.03 |
Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)
Work Hardening: None (High internal residual stress from extrusion)Cold Air Blast Only or Pure Deionized Water
Pressure: Cold air gun at 5 bar
CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.
Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.
Milling Direction: Climb milling mandatory to avoid chipping edge breakout.
- Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
- Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
- Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.
Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 2 mm)
What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 2 mm end mill?
What table feed rate and chip load should I program for 2 mm in Polycarbonate (Lexan / PC Thermoplastic)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Recent Calculations
No recent calculations saved yet.