1018 Mild Carbon Steel (Cold Rolled) — 1" (1.000 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 1018 Mild Carbon Steel (Cold Rolled) with a 1" (1.000 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 3,008 RPM at 240 m/min (787.4 SFM), with a profiling feed rate of 763 mm/min (30 IPM) and adjusted chip load of 0.0845 mm/tooth, achieving a material removal rate of 184.6 cm³/min (11.25 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math1018 Mild Carbon Steel (Cold Rolled) (1" (1.000 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 25.4 mm | 12.7 mm | 1× | 330 | 13 | 106.45 | 3.33 |
| Slotting (100% WOC) | 3F | 25.4 mm | 12.7 mm | 1× | 495 | 19.5 | 159.68 | 4.99 |
| Slotting (100% WOC) | 4F | 25.4 mm | 12.7 mm | 1× | 661 | 26 | 213.23 | 6.66 |
| Profiling / HEM (25% WOC) | 2F | 6.35 mm | 38.1 mm | 1.1547× | 508 | 20 | 122.9 | 3.84 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 6.35 mm | 38.1 mm | 1.1547× | 763 | 30 | 184.6 | 5.77 |
| Profiling / HEM (25% WOC) | 4F | 6.35 mm | 38.1 mm | 1.1547× | 1,017 | 40.1 | 246.05 | 7.69 |
| Adaptive Clearing (10% WOC) | 2F | 2.54 mm | 50.8 mm | 1.6667× | 734 | 28.9 | 94.71 | 2.96 |
| Adaptive Clearing (10% WOC) | 3F | 2.54 mm | 50.8 mm | 1.6667× | 1,101 | 43.3 | 142.06 | 4.44 |
| Adaptive Clearing (10% WOC) | 4F | 2.54 mm | 50.8 mm | 1.6667× | 1,468 | 57.8 | 189.42 | 5.92 |
Shop-Floor Machining Strategy for 1018 Mild Carbon Steel (Cold Rolled)
Work Hardening: ModerateFlood Coolant with 7-9% Soluble Oil or Dry with Air Blast for TiAlN Carbide
Pressure: 5 to 10 bar
With TiAlN coated carbide, dry cutting with air blast prevents thermal shock cycling on cutting edges.
Chip Flow: Low carbon steel can produce continuous gummy stringers if feed rate is too low. Keep chip load elevated.
Milling Direction: Always climb mill to manage tool heat dissipation into chips.
- Avoid rubbing at low feed rates. Feed fast enough to produce C-shaped curled blue/straw chips.
- TiAlN coating thrives on heat; avoid intermittent wet cooling that causes micro-cracking.
- 4-flute end mills deliver the best surface finish and wall straightness.
Frequently Asked CNC Questions (1018 Mild Carbon Steel (Cold Rolled) / 1" (1.000 in))
What is the recommended RPM for milling 1018 Mild Carbon Steel (Cold Rolled) with a 1" (1.000 in) end mill?
What table feed rate and chip load should I program for 1" (1.000 in) in 1018 Mild Carbon Steel (Cold Rolled)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 1018 Mild Carbon Steel (Cold Rolled)?
Recent Calculations
No recent calculations saved yet.