17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 1/4" (0.250 in) 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 1/4" (0.250 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 5,514 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 393 mm/min (15.4 IPM) and adjusted chip load of 0.0178 mm/tooth, achieving a material removal rate of 5.95 cm³/min (0.36 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (1/4" (0.250 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6.35 mm | 3.17 mm | 1× | 127 | 5 | 2.56 | 0.14 |
| Slotting (100% WOC) | 3F | 6.35 mm | 3.17 mm | 1× | 190 | 7.4 | 3.82 | 0.21 |
| Slotting (100% WOC) | 4F | 6.35 mm | 3.17 mm | 1× | 254 | 9.9 | 5.11 | 0.28 |
| Profiling / HEM (25% WOC) | 2F | 1.59 mm | 9.52 mm | 1.1541× | 196 | 7.7 | 2.97 | 0.16 |
| Profiling / HEM (25% WOC) | 3F | 1.59 mm | 9.52 mm | 1.1541× | 294 | 11.6 | 4.45 | 0.24 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 1.59 mm | 9.52 mm | 1.1541× | 393 | 15.4 | 5.95 | 0.32 |
| Adaptive Clearing (10% WOC) | 2F | 0.64 mm | 12.7 mm | 1.6609× | 282 | 11.1 | 2.29 | 0.12 |
| Adaptive Clearing (10% WOC) | 3F | 0.64 mm | 12.7 mm | 1.6609× | 423 | 16.7 | 3.44 | 0.19 |
| Adaptive Clearing (10% WOC) | 4F | 0.64 mm | 12.7 mm | 1.6609× | 565 | 22.3 | 4.59 | 0.25 |
Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)
Work Hardening: HighHigh-Pressure Flood Coolant with Synthetic Water-Soluble Fluid
Pressure: 30 to 70 bar
Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.
Chip Flow: Crisp, tight curled chips; high cutting forces generated.
Milling Direction: Always climb mill.
- In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
- Use thick-core end mills designed for hardened steels (4-5 flutes).
- Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.
Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 1/4" (0.250 in))
What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 1/4" (0.250 in) end mill?
What table feed rate and chip load should I program for 1/4" (0.250 in) in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Recent Calculations
No recent calculations saved yet.