17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 3/8" (0.375 in) 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 3/8" (0.375 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 3,676 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 360 mm/min (14.1 IPM) and adjusted chip load of 0.0245 mm/tooth, achieving a material removal rate of 12.24 cm³/min (0.74 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (3/8" (0.375 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 9.53 mm | 4.76 mm | 1× | 117 | 4.6 | 5.31 | 0.29 |
| Slotting (100% WOC) | 3F | 9.53 mm | 4.76 mm | 1× | 175 | 6.9 | 7.94 | 0.43 |
| Slotting (100% WOC) | 4F | 9.53 mm | 4.76 mm | 1× | 234 | 9.3 | 10.61 | 0.57 |
| Profiling / HEM (25% WOC) | 2F | 2.38 mm | 14.29 mm | 1.1549× | 180 | 7.1 | 6.12 | 0.33 |
| Profiling / HEM (25% WOC) | 3F | 2.38 mm | 14.29 mm | 1.1549× | 270 | 10.6 | 9.18 | 0.5 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 2.38 mm | 14.29 mm | 1.1549× | 360 | 14.1 | 12.24 | 0.66 |
| Adaptive Clearing (10% WOC) | 2F | 0.95 mm | 19.05 mm | 1.6686× | 260 | 10.2 | 4.71 | 0.26 |
| Adaptive Clearing (10% WOC) | 3F | 0.95 mm | 19.05 mm | 1.6686× | 390 | 15.3 | 7.06 | 0.38 |
| Adaptive Clearing (10% WOC) | 4F | 0.95 mm | 19.05 mm | 1.6686× | 521 | 20.4 | 9.43 | 0.51 |
Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)
Work Hardening: HighHigh-Pressure Flood Coolant with Synthetic Water-Soluble Fluid
Pressure: 30 to 70 bar
Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.
Chip Flow: Crisp, tight curled chips; high cutting forces generated.
Milling Direction: Always climb mill.
- In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
- Use thick-core end mills designed for hardened steels (4-5 flutes).
- Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.
Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 3/8" (0.375 in))
What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 3/8" (0.375 in) end mill?
What table feed rate and chip load should I program for 3/8" (0.375 in) in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Recent Calculations
No recent calculations saved yet.