Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 1" (1.000 in) 2-Flute Speeds & Feeds

ISO Group M / H 388 HB / 40-42 HRC

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
1,379 RPM
Surface Speed: 110 m/min (360.9 SFM)
Table Feed Rate F = RPM·z·fz
148 mm/min
5.8 IPM
Plunge/Ramp Rate: 52 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0538 mm/t
0.00212 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
35.81 cm³/min
2.17 in³/min
Power Required: 1.94 kW (2.6 HP)
Direct CNC Machining Solution

For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 1" (1.000 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 1,379 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 148 mm/min (5.8 IPM) and adjusted chip load of 0.0538 mm/tooth, achieving a material removal rate of 35.81 cm³/min (2.17 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) Stock CLIMB D = 25.4 mm (1") ae = 6.35 mm ap = 38.1 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 10.73 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (110 × 1000) / (π × 25.4) = 1,379 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 6.35/25.4 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0466 mm × 1.1547 = 0.0538 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 1,379 × 2 × 0.0538 = 148 mm/min (5.8 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (38.1 × 6.35 × 148) / 1000 = 35.81 cm³/min (2.17 in³/min)
Specific Cutting Force (kc) for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC): 2600 N/mm². Spindle drive efficiency η = 0.80.

17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (1" (1.000 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1" (1.000 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 25.4 mm 12.7 mm 1× 96 3.8 30.97 1.68
Slotting (100% WOC) 3F 25.4 mm 12.7 mm 1× 144 5.7 46.45 2.52
Slotting (100% WOC) 4F 25.4 mm 12.7 mm 1× 193 7.6 62.26 3.37
Profiling / HEM (25% WOC) CURRENT 2F 6.35 mm 38.1 mm 1.1547× 148 5.8 35.81 1.94
Profiling / HEM (25% WOC) 3F 6.35 mm 38.1 mm 1.1547× 223 8.8 53.95 2.92
Profiling / HEM (25% WOC) 4F 6.35 mm 38.1 mm 1.1547× 297 11.7 71.85 3.89
Adaptive Clearing (10% WOC) 2F 2.54 mm 50.8 mm 1.6667× 214 8.4 27.61 1.5
Adaptive Clearing (10% WOC) 3F 2.54 mm 50.8 mm 1.6667× 321 12.7 41.42 2.24
Adaptive Clearing (10% WOC) 4F 2.54 mm 50.8 mm 1.6667× 429 16.9 55.35 3

Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)

Work Hardening: High
Coolant & Lubrication Protocol

High-Pressure Flood Coolant with Synthetic Water-Soluble Fluid

Pressure: 30 to 70 bar

Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.

Chip Evacuation & Tool Path Guidance

Chip Flow: Crisp, tight curled chips; high cutting forces generated.

Milling Direction: Always climb mill.

Expert Machinist Tips:
  • In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
  • Use thick-core end mills designed for hardened steels (4-5 flutes).
  • Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.

Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 1" (1.000 in))

What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 1" (1.000 in) end mill?
For a 1" (1.000 in) (25.4 mm) TiAlN coated carbide end mill in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC), the baseline surface cutting speed is 110 m/min (360.9 SFM), which translates to a calculated spindle speed of 1,379 RPM. If using uncoated carbide, reduce surface speed to 85 m/min (280 SFM / 1065 RPM). For HSS cutters, speed must be restricted to 14 m/min (175 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1" (1.000 in) in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
At 1,379 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0538 mm/tooth (0.00212"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 148 mm/min (5.8 IPM). Ramping or plunging into material should be limited to 35% of table feed (52 mm/min / 2 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 6.35 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
High-Pressure Flood Coolant with Synthetic Water-Soluble Fluid. Pressure specification: 30 to 70 bar. Engineering rationale: Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.