17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 16 mm 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 16 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 2,188 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 244 mm/min (9.6 IPM) and adjusted chip load of 0.0372 mm/tooth, achieving a material removal rate of 23.42 cm³/min (1.43 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (16 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 16 mm | 8 mm | 1× | 105 | 4.2 | 13.44 | 0.73 |
| Slotting (100% WOC) | 3F | 16 mm | 8 mm | 1× | 158 | 6.2 | 20.22 | 1.1 |
| Slotting (100% WOC) | 4F | 16 mm | 8 mm | 1× | 211 | 8.3 | 27.01 | 1.46 |
| Profiling / HEM (25% WOC) | 2F | 4 mm | 24 mm | 1.1547× | 163 | 6.4 | 15.65 | 0.85 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 4 mm | 24 mm | 1.1547× | 244 | 9.6 | 23.42 | 1.27 |
| Profiling / HEM (25% WOC) | 4F | 4 mm | 24 mm | 1.1547× | 326 | 12.8 | 31.3 | 1.7 |
| Adaptive Clearing (10% WOC) | 2F | 1.6 mm | 32 mm | 1.6667× | 235 | 9.2 | 12.03 | 0.65 |
| Adaptive Clearing (10% WOC) | 3F | 1.6 mm | 32 mm | 1.6667× | 352 | 13.9 | 18.02 | 0.98 |
| Adaptive Clearing (10% WOC) | 4F | 1.6 mm | 32 mm | 1.6667× | 470 | 18.5 | 24.06 | 1.3 |
Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)
Work Hardening: HighHigh-Pressure Flood Coolant with Synthetic Water-Soluble Fluid
Pressure: 30 to 70 bar
Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.
Chip Flow: Crisp, tight curled chips; high cutting forces generated.
Milling Direction: Always climb mill.
- In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
- Use thick-core end mills designed for hardened steels (4-5 flutes).
- Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.
Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 16 mm)
What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 16 mm end mill?
What table feed rate and chip load should I program for 16 mm in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Recent Calculations
No recent calculations saved yet.