17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 2 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 2 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 17,507 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 490 mm/min (19.6 IPM) and adjusted chip load of 0.007 mm/tooth, achieving a material removal rate of 0.73 cm³/min (0.05 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (2 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 2 mm | 1 mm | 1× | 161 | 6.3 | 0.32 | 0.02 |
| Slotting (100% WOC) | 3F | 2 mm | 1 mm | 1× | 242 | 9.5 | 0.48 | 0.03 |
| Slotting (100% WOC) | 4F | 2 mm | 1 mm | 1× | 322 | 12.6 | 0.64 | 0.03 |
| Profiling / HEM (25% WOC) | 2F | 0.5 mm | 3 mm | 1.1547× | 245 | 9.8 | 0.37 | 0.02 |
| Profiling / HEM (25% WOC) | 3F | 0.5 mm | 3 mm | 1.1547× | 368 | 14.7 | 0.55 | 0.03 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 0.5 mm | 3 mm | 1.1547× | 490 | 19.6 | 0.73 | 0.04 |
| Adaptive Clearing (10% WOC) | 2F | 0.2 mm | 4 mm | 1.6667× | 357 | 14 | 0.29 | 0.02 |
| Adaptive Clearing (10% WOC) | 3F | 0.2 mm | 4 mm | 1.6667× | 536 | 21 | 0.43 | 0.02 |
| Adaptive Clearing (10% WOC) | 4F | 0.2 mm | 4 mm | 1.6667× | 714 | 28 | 0.57 | 0.03 |
Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)
Work Hardening: HighHigh-Pressure Flood Coolant with Synthetic Water-Soluble Fluid
Pressure: 30 to 70 bar
Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.
Chip Flow: Crisp, tight curled chips; high cutting forces generated.
Milling Direction: Always climb mill.
- In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
- Use thick-core end mills designed for hardened steels (4-5 flutes).
- Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.
Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 2 mm)
What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 2 mm end mill?
What table feed rate and chip load should I program for 2 mm in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Recent Calculations
No recent calculations saved yet.