17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 8 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 8 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 4,377 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 375 mm/min (14.7 IPM) and adjusted chip load of 0.0214 mm/tooth, achieving a material removal rate of 9 cm³/min (0.55 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (8 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 8 mm | 4 mm | 1× | 122 | 4.8 | 3.9 | 0.21 |
| Slotting (100% WOC) | 3F | 8 mm | 4 mm | 1× | 183 | 7.2 | 5.86 | 0.32 |
| Slotting (100% WOC) | 4F | 8 mm | 4 mm | 1× | 243 | 9.6 | 7.78 | 0.42 |
| Profiling / HEM (25% WOC) | 2F | 2 mm | 12 mm | 1.1547× | 187 | 7.4 | 4.49 | 0.24 |
| Profiling / HEM (25% WOC) | 3F | 2 mm | 12 mm | 1.1547× | 281 | 11 | 6.74 | 0.37 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 2 mm | 12 mm | 1.1547× | 375 | 14.7 | 9 | 0.49 |
| Adaptive Clearing (10% WOC) | 2F | 0.8 mm | 16 mm | 1.6667× | 270 | 10.6 | 3.46 | 0.19 |
| Adaptive Clearing (10% WOC) | 3F | 0.8 mm | 16 mm | 1.6667× | 404 | 15.9 | 5.17 | 0.28 |
| Adaptive Clearing (10% WOC) | 4F | 0.8 mm | 16 mm | 1.6667× | 539 | 21.2 | 6.9 | 0.37 |
Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)
Work Hardening: HighHigh-Pressure Flood Coolant with Synthetic Water-Soluble Fluid
Pressure: 30 to 70 bar
Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.
Chip Flow: Crisp, tight curled chips; high cutting forces generated.
Milling Direction: Always climb mill.
- In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
- Use thick-core end mills designed for hardened steels (4-5 flutes).
- Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.
Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 8 mm)
What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 8 mm end mill?
What table feed rate and chip load should I program for 8 mm in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Recent Calculations
No recent calculations saved yet.