Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 6 mm 4-Flute Speeds & Feeds

ISO Group M / H 388 HB / 40-42 HRC

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
5,836 RPM
Surface Speed: 110 m/min (360.9 SFM)
Table Feed Rate F = RPM·z·fz
397 mm/min
15.6 IPM
Plunge/Ramp Rate: 139 mm/min
Adjusted Chip Load CTF: 1.1547×
0.017 mm/t
0.00067 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
5.36 cm³/min
0.33 in³/min
Power Required: 0.29 kW (0.39 HP)
Direct CNC Machining Solution

For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 6 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 5,836 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 397 mm/min (15.6 IPM) and adjusted chip load of 0.017 mm/tooth, achieving a material removal rate of 5.36 cm³/min (0.33 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) Stock CLIMB D = 6 mm (0.2362") ae = 1.5 mm ap = 9 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.38 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (110 × 1000) / (π × 6) = 5,836 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1.5/6 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0147 mm × 1.1547 = 0.017 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 5,836 × 4 × 0.017 = 397 mm/min (15.6 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (9 × 1.5 × 397) / 1000 = 5.36 cm³/min (0.33 in³/min)
Specific Cutting Force (kc) for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC): 2600 N/mm². Spindle drive efficiency η = 0.80.

17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (6 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 6 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 6 mm 3 mm 1× 128 5 2.3 0.12
Slotting (100% WOC) 3F 6 mm 3 mm 1× 193 7.5 3.47 0.19
Slotting (100% WOC) 4F 6 mm 3 mm 1× 257 10 4.63 0.25
Profiling / HEM (25% WOC) 2F 1.5 mm 9 mm 1.1547× 198 7.8 2.67 0.14
Profiling / HEM (25% WOC) 3F 1.5 mm 9 mm 1.1547× 298 11.7 4.02 0.22
Profiling / HEM (25% WOC) CURRENT 4F 1.5 mm 9 mm 1.1547× 397 15.6 5.36 0.29
Adaptive Clearing (10% WOC) 2F 0.6 mm 12 mm 1.6667× 286 11.2 2.06 0.11
Adaptive Clearing (10% WOC) 3F 0.6 mm 12 mm 1.6667× 429 16.8 3.09 0.17
Adaptive Clearing (10% WOC) 4F 0.6 mm 12 mm 1.6667× 572 22.4 4.12 0.22

Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)

Work Hardening: High
Coolant & Lubrication Protocol

High-Pressure Flood Coolant with Synthetic Water-Soluble Fluid

Pressure: 30 to 70 bar

Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.

Chip Evacuation & Tool Path Guidance

Chip Flow: Crisp, tight curled chips; high cutting forces generated.

Milling Direction: Always climb mill.

Expert Machinist Tips:
  • In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
  • Use thick-core end mills designed for hardened steels (4-5 flutes).
  • Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.

Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 6 mm)

What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 6 mm end mill?
For a 6 mm (6 mm) TiAlN coated carbide end mill in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC), the baseline surface cutting speed is 110 m/min (360.9 SFM), which translates to a calculated spindle speed of 5,836 RPM. If using uncoated carbide, reduce surface speed to 85 m/min (280 SFM / 4509 RPM). For HSS cutters, speed must be restricted to 14 m/min (743 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 6 mm in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
At 5,836 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.017 mm/tooth (0.00067"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 397 mm/min (15.6 IPM). Ramping or plunging into material should be limited to 35% of table feed (139 mm/min / 5.5 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1.5 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
High-Pressure Flood Coolant with Synthetic Water-Soluble Fluid. Pressure specification: 30 to 70 bar. Engineering rationale: Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.