304 Austenitic Stainless Steel (18/8) — 1/4" (0.250 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 304 Austenitic Stainless Steel (18/8) with a 1/4" (0.250 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 7,018 RPM at 140 m/min (459.3 SFM), with a profiling feed rate of 427 mm/min (16.8 IPM) and adjusted chip load of 0.0203 mm/tooth, achieving a material removal rate of 6.46 cm³/min (0.39 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math304 Austenitic Stainless Steel (18/8) (1/4" (0.250 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6.35 mm | 3.17 mm | 1× | 185 | 7.3 | 3.72 | 0.17 |
| Slotting (100% WOC) | 3F | 6.35 mm | 3.17 mm | 1× | 278 | 10.9 | 5.6 | 0.26 |
| Slotting (100% WOC) | 4F | 6.35 mm | 3.17 mm | 1× | 371 | 14.6 | 7.47 | 0.34 |
| Profiling / HEM (25% WOC) | 2F | 1.59 mm | 9.52 mm | 1.1541× | 285 | 11.2 | 4.31 | 0.2 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 1.59 mm | 9.52 mm | 1.1541× | 427 | 16.8 | 6.46 | 0.3 |
| Profiling / HEM (25% WOC) | 4F | 1.59 mm | 9.52 mm | 1.1541× | 570 | 22.5 | 8.63 | 0.4 |
| Adaptive Clearing (10% WOC) | 2F | 0.64 mm | 12.7 mm | 1.6609× | 410 | 16.1 | 3.33 | 0.15 |
| Adaptive Clearing (10% WOC) | 3F | 0.64 mm | 12.7 mm | 1.6609× | 615 | 24.2 | 5 | 0.23 |
| Adaptive Clearing (10% WOC) | 4F | 0.64 mm | 12.7 mm | 1.6609× | 820 | 32.3 | 6.66 | 0.31 |
Shop-Floor Machining Strategy for 304 Austenitic Stainless Steel (18/8)
Work Hardening: EXTREMEHigh-Pressure Flood Coolant (10-12% Oil Concentration)
Pressure: 20 to 70 bar through-spindle preferred
Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.
Chip Flow: Tough, stringy, work-hardened chips. Chip clearance is paramount.
Milling Direction: MANDATORY climb milling. Conventional milling rubs before shearing and work-hardens the surface to 45+ HRC.
- NEVER DWELL OR RUB: Maintain positive feed per tooth at all times. If the cutter rubs, the workpiece work-hardens instantly.
- Use unequal helix angle (variable helix) 4-flute end mills to damp out chatter harmonics.
- AlTiN or multi-layer nano-coatings provide critical barrier against built-up edge and notch wear.
Frequently Asked CNC Questions (304 Austenitic Stainless Steel (18/8) / 1/4" (0.250 in))
What is the recommended RPM for milling 304 Austenitic Stainless Steel (18/8) with a 1/4" (0.250 in) end mill?
What table feed rate and chip load should I program for 1/4" (0.250 in) in 304 Austenitic Stainless Steel (18/8)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 304 Austenitic Stainless Steel (18/8)?
Recent Calculations
No recent calculations saved yet.