Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

304 Austenitic Stainless Steel (18/8) — 3/8" (0.375 in) 3-Flute Speeds & Feeds

ISO Group M 180 HB / 88 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
4,679 RPM
Surface Speed: 140 m/min (459.3 SFM)
Table Feed Rate F = RPM·z·fz
394 mm/min
15.6 IPM
Plunge/Ramp Rate: 138 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0281 mm/t
0.00111 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
13.4 cm³/min
0.82 in³/min
Power Required: 0.61 kW (0.82 HP)
Direct CNC Machining Solution

For milling 304 Austenitic Stainless Steel (18/8) with a 3/8" (0.375 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 4,679 RPM at 140 m/min (459.3 SFM), with a profiling feed rate of 394 mm/min (15.6 IPM) and adjusted chip load of 0.0281 mm/tooth, achieving a material removal rate of 13.4 cm³/min (0.82 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
304 Austenitic Stainless Steel (18/8) Stock CLIMB D = 9.525 mm (0.375") ae = 2.38 mm ap = 14.29 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 1 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (140 × 1000) / (π × 9.525) = 4,679 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 2.38/9.525 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0243 mm × 1.1549 = 0.0281 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 4,679 × 3 × 0.0281 = 394 mm/min (15.6 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (14.29 × 2.38 × 394) / 1000 = 13.4 cm³/min (0.82 in³/min)
Specific Cutting Force (kc) for 304 Austenitic Stainless Steel (18/8): 2200 N/mm². Spindle drive efficiency η = 0.80.

304 Austenitic Stainless Steel (18/8) (3/8" (0.375 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/8" (0.375 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 9.53 mm 4.76 mm 1× 170 6.7 7.71 0.35
Slotting (100% WOC) 3F 9.53 mm 4.76 mm 1× 255 10.1 11.57 0.53
Slotting (100% WOC) 4F 9.53 mm 4.76 mm 1× 341 13.5 15.47 0.71
Profiling / HEM (25% WOC) 2F 2.38 mm 14.29 mm 1.1549× 263 10.4 8.94 0.41
Profiling / HEM (25% WOC) CURRENT 3F 2.38 mm 14.29 mm 1.1549× 394 15.6 13.4 0.61
Profiling / HEM (25% WOC) 4F 2.38 mm 14.29 mm 1.1549× 526 20.8 17.89 0.82
Adaptive Clearing (10% WOC) 2F 0.95 mm 19.05 mm 1.6686× 379 14.9 6.86 0.31
Adaptive Clearing (10% WOC) 3F 0.95 mm 19.05 mm 1.6686× 568 22.3 10.28 0.47
Adaptive Clearing (10% WOC) 4F 0.95 mm 19.05 mm 1.6686× 758 29.8 13.72 0.63

Shop-Floor Machining Strategy for 304 Austenitic Stainless Steel (18/8)

Work Hardening: EXTREME
Coolant & Lubrication Protocol

High-Pressure Flood Coolant (10-12% Oil Concentration)

Pressure: 20 to 70 bar through-spindle preferred

Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.

Chip Evacuation & Tool Path Guidance

Chip Flow: Tough, stringy, work-hardened chips. Chip clearance is paramount.

Milling Direction: MANDATORY climb milling. Conventional milling rubs before shearing and work-hardens the surface to 45+ HRC.

Expert Machinist Tips:
  • NEVER DWELL OR RUB: Maintain positive feed per tooth at all times. If the cutter rubs, the workpiece work-hardens instantly.
  • Use unequal helix angle (variable helix) 4-flute end mills to damp out chatter harmonics.
  • AlTiN or multi-layer nano-coatings provide critical barrier against built-up edge and notch wear.

Frequently Asked CNC Questions (304 Austenitic Stainless Steel (18/8) / 3/8" (0.375 in))

What is the recommended RPM for milling 304 Austenitic Stainless Steel (18/8) with a 3/8" (0.375 in) end mill?
For a 3/8" (0.375 in) (9.525 mm) TiAlN coated carbide end mill in 304 Austenitic Stainless Steel (18/8), the baseline surface cutting speed is 140 m/min (459.3 SFM), which translates to a calculated spindle speed of 4,679 RPM. If using uncoated carbide, reduce surface speed to 115 m/min (380 SFM / 3843 RPM). For HSS cutters, speed must be restricted to 20 m/min (668 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/8" (0.375 in) in 304 Austenitic Stainless Steel (18/8)?
At 4,679 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0281 mm/tooth (0.00111"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 394 mm/min (15.6 IPM). Ramping or plunging into material should be limited to 35% of table feed (138 mm/min / 5.5 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 2.38 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 304 Austenitic Stainless Steel (18/8)?
High-Pressure Flood Coolant (10-12% Oil Concentration). Pressure specification: 20 to 70 bar through-spindle preferred. Engineering rationale: Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.