Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

304 Austenitic Stainless Steel (18/8) — 1/8" (0.125 in) 3-Flute Speeds & Feeds

ISO Group M 180 HB / 88 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
14,036 RPM
Surface Speed: 140 m/min (459.3 SFM)
Table Feed Rate F = RPM·z·fz
493 mm/min
19.4 IPM
Plunge/Ramp Rate: 173 mm/min
Adjusted Chip Load CTF: 1.1565×
0.0117 mm/t
0.00046 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
1.85 cm³/min
0.11 in³/min
Power Required: 0.08 kW (0.11 HP)
Direct CNC Machining Solution

For milling 304 Austenitic Stainless Steel (18/8) with a 1/8" (0.125 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 14,036 RPM at 140 m/min (459.3 SFM), with a profiling feed rate of 493 mm/min (19.4 IPM) and adjusted chip load of 0.0117 mm/tooth, achieving a material removal rate of 1.85 cm³/min (0.11 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
304 Austenitic Stainless Steel (18/8) Stock CLIMB D = 3.175 mm (0.125") ae = 0.79 mm ap = 4.76 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1565×
Spindle Torque 0.05 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (140 × 1000) / (π × 3.175) = 14,036 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.79/3.175 = 0.25 → CTF = 1.1565×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0101 mm × 1.1565 = 0.0117 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 14,036 × 3 × 0.0117 = 493 mm/min (19.4 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (4.76 × 0.79 × 493) / 1000 = 1.85 cm³/min (0.11 in³/min)
Specific Cutting Force (kc) for 304 Austenitic Stainless Steel (18/8): 2200 N/mm². Spindle drive efficiency η = 0.80.

304 Austenitic Stainless Steel (18/8) (1/8" (0.125 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1/8" (0.125 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 3.17 mm 1.59 mm 1× 213 8.4 1.07 0.05
Slotting (100% WOC) 3F 3.17 mm 1.59 mm 1× 320 12.6 1.61 0.07
Slotting (100% WOC) 4F 3.17 mm 1.59 mm 1× 427 16.8 2.15 0.1
Profiling / HEM (25% WOC) 2F 0.79 mm 4.76 mm 1.1565× 328 12.9 1.23 0.06
Profiling / HEM (25% WOC) CURRENT 3F 0.79 mm 4.76 mm 1.1565× 493 19.4 1.85 0.08
Profiling / HEM (25% WOC) 4F 0.79 mm 4.76 mm 1.1565× 657 25.8 2.47 0.11
Adaptive Clearing (10% WOC) 2F 0.32 mm 6.35 mm 1.6609× 472 18.5 0.96 0.04
Adaptive Clearing (10% WOC) 3F 0.32 mm 6.35 mm 1.6609× 707 27.8 1.44 0.07
Adaptive Clearing (10% WOC) 4F 0.32 mm 6.35 mm 1.6609× 943 37.1 1.92 0.09

Shop-Floor Machining Strategy for 304 Austenitic Stainless Steel (18/8)

Work Hardening: EXTREME
Coolant & Lubrication Protocol

High-Pressure Flood Coolant (10-12% Oil Concentration)

Pressure: 20 to 70 bar through-spindle preferred

Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.

Chip Evacuation & Tool Path Guidance

Chip Flow: Tough, stringy, work-hardened chips. Chip clearance is paramount.

Milling Direction: MANDATORY climb milling. Conventional milling rubs before shearing and work-hardens the surface to 45+ HRC.

Expert Machinist Tips:
  • NEVER DWELL OR RUB: Maintain positive feed per tooth at all times. If the cutter rubs, the workpiece work-hardens instantly.
  • Use unequal helix angle (variable helix) 4-flute end mills to damp out chatter harmonics.
  • AlTiN or multi-layer nano-coatings provide critical barrier against built-up edge and notch wear.

Frequently Asked CNC Questions (304 Austenitic Stainless Steel (18/8) / 1/8" (0.125 in))

What is the recommended RPM for milling 304 Austenitic Stainless Steel (18/8) with a 1/8" (0.125 in) end mill?
For a 1/8" (0.125 in) (3.175 mm) TiAlN coated carbide end mill in 304 Austenitic Stainless Steel (18/8), the baseline surface cutting speed is 140 m/min (459.3 SFM), which translates to a calculated spindle speed of 14,036 RPM. If using uncoated carbide, reduce surface speed to 115 m/min (380 SFM / 11529 RPM). For HSS cutters, speed must be restricted to 20 m/min (2005 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1/8" (0.125 in) in 304 Austenitic Stainless Steel (18/8)?
At 14,036 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0117 mm/tooth (0.00046"/tooth) after applying a radial chip thinning factor (CTF) of 1.1565×. This yields a table feed rate of 493 mm/min (19.4 IPM). Ramping or plunging into material should be limited to 35% of table feed (173 mm/min / 6.8 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.79 mm), the Chip Thinning Factor is 1.1565×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 304 Austenitic Stainless Steel (18/8)?
High-Pressure Flood Coolant (10-12% Oil Concentration). Pressure specification: 20 to 70 bar through-spindle preferred. Engineering rationale: Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.