Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

7075-T6 Aerospace Aluminum — 1/8" (0.125 in) 3-Flute Speeds & Feeds

ISO Group N 150 HB / 87 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
58,148 RPM
Surface Speed: 580 m/min (1902.9 SFM)
Table Feed Rate F = RPM·z·fz
3,559 mm/min
139.6 IPM
Plunge/Ramp Rate: 1246 mm/min
Adjusted Chip Load CTF: 1.1565×
0.0204 mm/t
0.0008 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
13.38 cm³/min
0.81 in³/min
Power Required: 0.24 kW (0.32 HP)
Direct CNC Machining Solution

For milling 7075-T6 Aerospace Aluminum with a 1/8" (0.125 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 58,148 RPM at 580 m/min (1902.9 SFM), with a profiling feed rate of 3,559 mm/min (139.6 IPM) and adjusted chip load of 0.0204 mm/tooth, achieving a material removal rate of 13.38 cm³/min (0.81 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
7075-T6 Aerospace Aluminum Stock CLIMB D = 3.175 mm (0.125") ae = 0.79 mm ap = 4.76 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1565×
Spindle Torque 0.03 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (580 × 1000) / (π × 3.175) = 58,148 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.79/3.175 = 0.25 → CTF = 1.1565×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0176 mm × 1.1565 = 0.0204 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 58,148 × 3 × 0.0204 = 3,559 mm/min (139.6 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (4.76 × 0.79 × 3559) / 1000 = 13.38 cm³/min (0.81 in³/min)
Specific Cutting Force (kc) for 7075-T6 Aerospace Aluminum: 850 N/mm². Spindle drive efficiency η = 0.80.

7075-T6 Aerospace Aluminum (1/8" (0.125 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1/8" (0.125 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 3.17 mm 1.59 mm 1× 1,535 60.5 7.74 0.14
Slotting (100% WOC) 3F 3.17 mm 1.59 mm 1× 2,303 90.7 11.61 0.21
Slotting (100% WOC) 4F 3.17 mm 1.59 mm 1× 3,070 120.9 15.47 0.27
Profiling / HEM (25% WOC) 2F 0.79 mm 4.76 mm 1.1565× 2,372 93 8.92 0.16
Profiling / HEM (25% WOC) CURRENT 3F 0.79 mm 4.76 mm 1.1565× 3,559 139.6 13.38 0.24
Profiling / HEM (25% WOC) 4F 0.79 mm 4.76 mm 1.1565× 4,745 186.1 17.84 0.32
Adaptive Clearing (10% WOC) 2F 0.32 mm 6.35 mm 1.6609× 3,396 133.7 6.9 0.12
Adaptive Clearing (10% WOC) 3F 0.32 mm 6.35 mm 1.6609× 5,094 200.6 10.35 0.18
Adaptive Clearing (10% WOC) 4F 0.32 mm 6.35 mm 1.6609× 6,792 267.5 13.8 0.24

Shop-Floor Machining Strategy for 7075-T6 Aerospace Aluminum

Work Hardening: Low
Coolant & Lubrication Protocol

Flood Coolant with 8-10% Synthetic Soluble Oil Concentration

Pressure: Standard flood (5 bar minimum)

Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.

Chip Evacuation & Tool Path Guidance

Chip Flow: Excellent short crisp chips compared to 6061. Can run 3-flute tools at aggressive feeds.

Milling Direction: Climb milling gives mirror surface finishes.

Expert Machinist Tips:
  • High zinc content gives higher tensile strength; chips shear off crisply.
  • Maintain tool rigidity; deflection causes dimensional drift on tight aerospace tolerances.
  • Ideal candidate for High-Speed Machining (HSM) with high axial depth and light radial stepover.

Frequently Asked CNC Questions (7075-T6 Aerospace Aluminum / 1/8" (0.125 in))

What is the recommended RPM for milling 7075-T6 Aerospace Aluminum with a 1/8" (0.125 in) end mill?
For a 1/8" (0.125 in) (3.175 mm) TiAlN coated carbide end mill in 7075-T6 Aerospace Aluminum, the baseline surface cutting speed is 580 m/min (1902.9 SFM), which translates to a calculated spindle speed of 58,148 RPM. If using uncoated carbide, reduce surface speed to 480 m/min (1600 SFM / 48122 RPM). For HSS cutters, speed must be restricted to 100 m/min (10026 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1/8" (0.125 in) in 7075-T6 Aerospace Aluminum?
At 58,148 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0204 mm/tooth (0.0008"/tooth) after applying a radial chip thinning factor (CTF) of 1.1565×. This yields a table feed rate of 3559 mm/min (139.6 IPM). Ramping or plunging into material should be limited to 35% of table feed (1246 mm/min / 48.9 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.79 mm), the Chip Thinning Factor is 1.1565×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 7075-T6 Aerospace Aluminum?
Flood Coolant with 8-10% Synthetic Soluble Oil Concentration. Pressure specification: Standard flood (5 bar minimum). Engineering rationale: Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.