304 Austenitic Stainless Steel (18/8) — 10 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 304 Austenitic Stainless Steel (18/8) with a 10 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 4,456 RPM at 140 m/min (459.3 SFM), with a profiling feed rate of 259 mm/min (10.2 IPM) and adjusted chip load of 0.0291 mm/tooth, achieving a material removal rate of 9.71 cm³/min (0.59 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math304 Austenitic Stainless Steel (18/8) (10 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 10 mm | 5 mm | 1× | 168 | 6.6 | 8.4 | 0.38 |
| Slotting (100% WOC) | 3F | 10 mm | 5 mm | 1× | 253 | 9.9 | 12.65 | 0.58 |
| Slotting (100% WOC) | 4F | 10 mm | 5 mm | 1× | 337 | 13.2 | 16.85 | 0.77 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 2.5 mm | 15 mm | 1.1547× | 259 | 10.2 | 9.71 | 0.45 |
| Profiling / HEM (25% WOC) | 3F | 2.5 mm | 15 mm | 1.1547× | 389 | 15.4 | 14.59 | 0.67 |
| Profiling / HEM (25% WOC) | 4F | 2.5 mm | 15 mm | 1.1547× | 519 | 20.5 | 19.46 | 0.89 |
| Adaptive Clearing (10% WOC) | 2F | 1 mm | 20 mm | 1.6667× | 374 | 14.7 | 7.48 | 0.34 |
| Adaptive Clearing (10% WOC) | 3F | 1 mm | 20 mm | 1.6667× | 561 | 22.1 | 11.22 | 0.51 |
| Adaptive Clearing (10% WOC) | 4F | 1 mm | 20 mm | 1.6667× | 749 | 29.4 | 14.98 | 0.69 |
Shop-Floor Machining Strategy for 304 Austenitic Stainless Steel (18/8)
Work Hardening: EXTREMEHigh-Pressure Flood Coolant (10-12% Oil Concentration)
Pressure: 20 to 70 bar through-spindle preferred
Abundant coolant is required to carry away intense heat. Poor thermal conductivity means heat stays in the cut zone.
Chip Flow: Tough, stringy, work-hardened chips. Chip clearance is paramount.
Milling Direction: MANDATORY climb milling. Conventional milling rubs before shearing and work-hardens the surface to 45+ HRC.
- NEVER DWELL OR RUB: Maintain positive feed per tooth at all times. If the cutter rubs, the workpiece work-hardens instantly.
- Use unequal helix angle (variable helix) 4-flute end mills to damp out chatter harmonics.
- AlTiN or multi-layer nano-coatings provide critical barrier against built-up edge and notch wear.
Frequently Asked CNC Questions (304 Austenitic Stainless Steel (18/8) / 10 mm)
What is the recommended RPM for milling 304 Austenitic Stainless Steel (18/8) with a 10 mm end mill?
What table feed rate and chip load should I program for 10 mm in 304 Austenitic Stainless Steel (18/8)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 304 Austenitic Stainless Steel (18/8)?
Recent Calculations
No recent calculations saved yet.