316 Marine Grade Stainless Steel (with Molybdenum) — 1/4" (0.250 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 316 Marine Grade Stainless Steel (with Molybdenum) with a 1/4" (0.250 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 6,266 RPM at 125 m/min (410.1 SFM), with a profiling feed rate of 363 mm/min (14.3 IPM) and adjusted chip load of 0.0193 mm/tooth, achieving a material removal rate of 5.49 cm³/min (0.34 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math316 Marine Grade Stainless Steel (with Molybdenum) (1/4" (0.250 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6.35 mm | 3.17 mm | 1× | 157 | 6.1 | 3.16 | 0.15 |
| Slotting (100% WOC) | 3F | 6.35 mm | 3.17 mm | 1× | 235 | 9.2 | 4.73 | 0.23 |
| Slotting (100% WOC) | 4F | 6.35 mm | 3.17 mm | 1× | 313 | 12.3 | 6.3 | 0.3 |
| Profiling / HEM (25% WOC) | 2F | 1.59 mm | 9.52 mm | 1.1541× | 242 | 9.5 | 3.66 | 0.18 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 1.59 mm | 9.52 mm | 1.1541× | 363 | 14.3 | 5.49 | 0.26 |
| Profiling / HEM (25% WOC) | 4F | 1.59 mm | 9.52 mm | 1.1541× | 484 | 19 | 7.33 | 0.35 |
| Adaptive Clearing (10% WOC) | 2F | 0.64 mm | 12.7 mm | 1.6609× | 347 | 13.7 | 2.82 | 0.14 |
| Adaptive Clearing (10% WOC) | 3F | 0.64 mm | 12.7 mm | 1.6609× | 521 | 20.5 | 4.23 | 0.2 |
| Adaptive Clearing (10% WOC) | 4F | 0.64 mm | 12.7 mm | 1.6609× | 694 | 27.3 | 5.64 | 0.27 |
Shop-Floor Machining Strategy for 316 Marine Grade Stainless Steel (with Molybdenum)
Work Hardening: EXTREMEHeavy Flood Coolant with Extreme Pressure (EP) Additives
Pressure: 20 bar minimum
Molybdenum addition increases chemical and high-temp shear toughness, requiring superior lubricity.
Chip Flow: High tendency for chips to weld to cutting edges if feed pauses.
Milling Direction: Mandatory climb milling.
- Reduce SFM by 10-15% compared to 304 stainless; keep chip load firm.
- Corner chamfer or radiused cutters prevent premature notch wear on the depth-of-cut line.
- Use high-feed milling or trochoidal toolpaths to spread wear along the full flute length.
Frequently Asked CNC Questions (316 Marine Grade Stainless Steel (with Molybdenum) / 1/4" (0.250 in))
What is the recommended RPM for milling 316 Marine Grade Stainless Steel (with Molybdenum) with a 1/4" (0.250 in) end mill?
What table feed rate and chip load should I program for 1/4" (0.250 in) in 316 Marine Grade Stainless Steel (with Molybdenum)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 316 Marine Grade Stainless Steel (with Molybdenum)?
Recent Calculations
No recent calculations saved yet.