316 Marine Grade Stainless Steel (with Molybdenum) — 4 mm 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 316 Marine Grade Stainless Steel (with Molybdenum) with a 4 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 9,947 RPM at 125 m/min (410.1 SFM), with a profiling feed rate of 397 mm/min (15.5 IPM) and adjusted chip load of 0.0133 mm/tooth, achieving a material removal rate of 2.38 cm³/min (0.14 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math316 Marine Grade Stainless Steel (with Molybdenum) (4 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 4 mm | 2 mm | 1× | 171 | 6.8 | 1.37 | 0.07 |
| Slotting (100% WOC) | 3F | 4 mm | 2 mm | 1× | 257 | 10.1 | 2.06 | 0.1 |
| Slotting (100% WOC) | 4F | 4 mm | 2 mm | 1× | 342 | 13.5 | 2.74 | 0.13 |
| Profiling / HEM (25% WOC) | 2F | 1 mm | 6 mm | 1.1547× | 265 | 10.3 | 1.59 | 0.08 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 1 mm | 6 mm | 1.1547× | 397 | 15.5 | 2.38 | 0.11 |
| Profiling / HEM (25% WOC) | 4F | 1 mm | 6 mm | 1.1547× | 529 | 20.7 | 3.17 | 0.15 |
| Adaptive Clearing (10% WOC) | 2F | 0.4 mm | 8 mm | 1.6667× | 382 | 15.1 | 1.22 | 0.06 |
| Adaptive Clearing (10% WOC) | 3F | 0.4 mm | 8 mm | 1.6667× | 573 | 22.7 | 1.83 | 0.09 |
| Adaptive Clearing (10% WOC) | 4F | 0.4 mm | 8 mm | 1.6667× | 764 | 30.2 | 2.44 | 0.12 |
Shop-Floor Machining Strategy for 316 Marine Grade Stainless Steel (with Molybdenum)
Work Hardening: EXTREMEHeavy Flood Coolant with Extreme Pressure (EP) Additives
Pressure: 20 bar minimum
Molybdenum addition increases chemical and high-temp shear toughness, requiring superior lubricity.
Chip Flow: High tendency for chips to weld to cutting edges if feed pauses.
Milling Direction: Mandatory climb milling.
- Reduce SFM by 10-15% compared to 304 stainless; keep chip load firm.
- Corner chamfer or radiused cutters prevent premature notch wear on the depth-of-cut line.
- Use high-feed milling or trochoidal toolpaths to spread wear along the full flute length.
Frequently Asked CNC Questions (316 Marine Grade Stainless Steel (with Molybdenum) / 4 mm)
What is the recommended RPM for milling 316 Marine Grade Stainless Steel (with Molybdenum) with a 4 mm end mill?
What table feed rate and chip load should I program for 4 mm in 316 Marine Grade Stainless Steel (with Molybdenum)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 316 Marine Grade Stainless Steel (with Molybdenum)?
Recent Calculations
No recent calculations saved yet.