Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) — 3/16" (0.1875 in) 2-Flute Speeds & Feeds

ISO Group P 280-320 HB / 28-32 HRC

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
12,700 RPM
Surface Speed: 190 m/min (623.4 SFM)
Table Feed Rate F = RPM·z·fz
490 mm/min
19.3 IPM
Plunge/Ramp Rate: 172 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0193 mm/t
0.00076 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
4.16 cm³/min
0.25 in³/min
Power Required: 0.18 kW (0.24 HP)
Direct CNC Machining Solution

For milling 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) with a 3/16" (0.1875 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 12,700 RPM at 190 m/min (623.4 SFM), with a profiling feed rate of 490 mm/min (19.3 IPM) and adjusted chip load of 0.0193 mm/tooth, achieving a material removal rate of 4.16 cm³/min (0.25 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) Stock CLIMB D = 4.762 mm (0.1875") ae = 1.19 mm ap = 7.14 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 0.11 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (190 × 1000) / (π × 4.762) = 12,700 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1.19/4.762 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0167 mm × 1.1549 = 0.0193 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 12,700 × 2 × 0.0193 = 490 mm/min (19.3 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (7.14 × 1.19 × 490) / 1000 = 4.16 cm³/min (0.25 in³/min)
Specific Cutting Force (kc) for 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC): 2100 N/mm². Spindle drive efficiency η = 0.80.

4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) (3/16" (0.1875 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/16" (0.1875 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 4.76 mm 2.38 mm 1× 318 12.4 3.6 0.16
Slotting (100% WOC) 3F 4.76 mm 2.38 mm 1× 476 18.7 5.39 0.24
Slotting (100% WOC) 4F 4.76 mm 2.38 mm 1× 635 24.9 7.19 0.31
Profiling / HEM (25% WOC) CURRENT 2F 1.19 mm 7.14 mm 1.1549× 490 19.3 4.16 0.18
Profiling / HEM (25% WOC) 3F 1.19 mm 7.14 mm 1.1549× 735 29 6.25 0.27
Profiling / HEM (25% WOC) 4F 1.19 mm 7.14 mm 1.1549× 980 38.6 8.33 0.36
Adaptive Clearing (10% WOC) 2F 0.48 mm 9.52 mm 1.6608× 704 27.7 3.22 0.14
Adaptive Clearing (10% WOC) 3F 0.48 mm 9.52 mm 1.6608× 1,055 41.5 4.82 0.21
Adaptive Clearing (10% WOC) 4F 0.48 mm 9.52 mm 1.6608× 1,407 55.4 6.43 0.28

Shop-Floor Machining Strategy for 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC)

Work Hardening: Moderate-High
Coolant & Lubrication Protocol

Air Blast for TiAlN Coated Carbide; Flood Coolant for HSS

Pressure: 6 bar air blast or 20 bar high-pressure flood

Thermal shock from erratic coolant flow causes micro-chipping of carbide cutting edges.

Chip Evacuation & Tool Path Guidance

Chip Flow: Short curled chips form with proper feed; excellent surface finish potential.

Milling Direction: Climb milling essential to enter at thickest chip portion.

Expert Machinist Tips:
  • Pre-hardened 4140 (HT) machines cleanly with rigid setups and AlTiN or TiAlN coated tooling.
  • Use high-efficiency milling (HEM): 8-12% ae radial engagement with 1.5x-2.0x ap depth of cut.
  • Keep tool stickout as short as possible to eliminate chatter harmonics.

Frequently Asked CNC Questions (4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) / 3/16" (0.1875 in))

What is the recommended RPM for milling 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC) with a 3/16" (0.1875 in) end mill?
For a 3/16" (0.1875 in) (4.762 mm) TiAlN coated carbide end mill in 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC), the baseline surface cutting speed is 190 m/min (623.4 SFM), which translates to a calculated spindle speed of 12,700 RPM. If using uncoated carbide, reduce surface speed to 150 m/min (500 SFM / 10027 RPM). For HSS cutters, speed must be restricted to 24 m/min (1604 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/16" (0.1875 in) in 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC)?
At 12,700 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0193 mm/tooth (0.00076"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 490 mm/min (19.3 IPM). Ramping or plunging into material should be limited to 35% of table feed (172 mm/min / 6.8 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1.19 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 4140 Chromium-Molybdenum Alloy Steel (Pre-hardened 28-32 HRC)?
Air Blast for TiAlN Coated Carbide; Flood Coolant for HSS. Pressure specification: 6 bar air blast or 20 bar high-pressure flood. Engineering rationale: Thermal shock from erratic coolant flow causes micro-chipping of carbide cutting edges.