6061-T6 Aluminum — 3/16" (0.1875 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 6061-T6 Aluminum with a 3/16" (0.1875 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 43,448 RPM at 650 m/min (2132.5 SFM), with a profiling feed rate of 3,923 mm/min (155.1 IPM) and adjusted chip load of 0.0301 mm/tooth, achieving a material removal rate of 33.33 cm³/min (2.04 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math6061-T6 Aluminum (3/16" (0.1875 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 4.76 mm | 2.38 mm | 1× | 1,703 | 66.9 | 19.29 | 0.28 |
| Slotting (100% WOC) | 3F | 4.76 mm | 2.38 mm | 1× | 2,555 | 100.4 | 28.95 | 0.42 |
| Slotting (100% WOC) | 4F | 4.76 mm | 2.38 mm | 1× | 3,406 | 133.8 | 38.59 | 0.56 |
| Profiling / HEM (25% WOC) | 2F | 1.19 mm | 7.14 mm | 1.1549× | 2,616 | 103.4 | 22.23 | 0.32 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 1.19 mm | 7.14 mm | 1.1549× | 3,923 | 155.1 | 33.33 | 0.49 |
| Profiling / HEM (25% WOC) | 4F | 1.19 mm | 7.14 mm | 1.1549× | 5,231 | 206.8 | 44.45 | 0.65 |
| Adaptive Clearing (10% WOC) | 2F | 0.48 mm | 9.52 mm | 1.6608× | 3,763 | 147.7 | 17.2 | 0.25 |
| Adaptive Clearing (10% WOC) | 3F | 0.48 mm | 9.52 mm | 1.6608× | 5,644 | 221.6 | 25.79 | 0.38 |
| Adaptive Clearing (10% WOC) | 4F | 0.48 mm | 9.52 mm | 1.6608× | 7,525 | 295.4 | 34.39 | 0.5 |
Shop-Floor Machining Strategy for 6061-T6 Aluminum
Work Hardening: LowHigh-Pressure Flood Coolant or MQL Air Blast with Alcohol/Oil Mist
Pressure: Flood at 5-10 bar; Through-Spindle 20 bar
Lubricity is critical. Dry cutting risks instantaneous aluminum welding to tool flutes and catastrophic cutter snap.
Chip Flow: Use polished flutes (ZrN or DLC coating) and 2 or 3 flutes to prevent chip re-cutting.
Milling Direction: Always climb mill. Conventional milling causes built-up edge on the tool face.
- Max spindle speed is usually preferred; feed fast to maintain minimum chip thickness (>0.02 mm) to prevent rubbing.
- In deep pocketing, utilize high pressure air blast to blast chips out of the cavity.
- For high-speed trochoidal slotting, use 10-15% radial stepover (ae) at 2.0x-3.0x axial depth (ap).
Frequently Asked CNC Questions (6061-T6 Aluminum / 3/16" (0.1875 in))
What is the recommended RPM for milling 6061-T6 Aluminum with a 3/16" (0.1875 in) end mill?
What table feed rate and chip load should I program for 3/16" (0.1875 in) in 6061-T6 Aluminum?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 6061-T6 Aluminum?
Recent Calculations
No recent calculations saved yet.