Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

7075-T6 Aerospace Aluminum — 3/16" (0.1875 in) 3-Flute Speeds & Feeds

ISO Group N 150 HB / 87 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
38,769 RPM
Surface Speed: 580 m/min (1902.9 SFM)
Table Feed Rate F = RPM·z·fz
3,280 mm/min
129.1 IPM
Plunge/Ramp Rate: 1148 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0282 mm/t
0.00111 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
27.87 cm³/min
1.7 in³/min
Power Required: 0.49 kW (0.66 HP)
Direct CNC Machining Solution

For milling 7075-T6 Aerospace Aluminum with a 3/16" (0.1875 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 38,769 RPM at 580 m/min (1902.9 SFM), with a profiling feed rate of 3,280 mm/min (129.1 IPM) and adjusted chip load of 0.0282 mm/tooth, achieving a material removal rate of 27.87 cm³/min (1.7 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
7075-T6 Aerospace Aluminum Stock CLIMB D = 4.762 mm (0.1875") ae = 1.19 mm ap = 7.14 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 0.1 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (580 × 1000) / (π × 4.762) = 38,769 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1.19/4.762 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0244 mm × 1.1549 = 0.0282 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 38,769 × 3 × 0.0282 = 3,280 mm/min (129.1 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (7.14 × 1.19 × 3280) / 1000 = 27.87 cm³/min (1.7 in³/min)
Specific Cutting Force (kc) for 7075-T6 Aerospace Aluminum: 850 N/mm². Spindle drive efficiency η = 0.80.

7075-T6 Aerospace Aluminum (3/16" (0.1875 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/16" (0.1875 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 4.76 mm 2.38 mm 1× 1,419 55.8 16.08 0.28
Slotting (100% WOC) 3F 4.76 mm 2.38 mm 1× 2,128 83.7 24.11 0.43
Slotting (100% WOC) 4F 4.76 mm 2.38 mm 1× 2,838 111.7 32.15 0.57
Profiling / HEM (25% WOC) 2F 1.19 mm 7.14 mm 1.1549× 2,187 86.1 18.58 0.33
Profiling / HEM (25% WOC) CURRENT 3F 1.19 mm 7.14 mm 1.1549× 3,280 129.1 27.87 0.49
Profiling / HEM (25% WOC) 4F 1.19 mm 7.14 mm 1.1549× 4,373 172.1 37.16 0.66
Adaptive Clearing (10% WOC) 2F 0.48 mm 9.52 mm 1.6608× 3,140 123.3 14.35 0.25
Adaptive Clearing (10% WOC) 3F 0.48 mm 9.52 mm 1.6608× 4,710 184.9 21.52 0.38
Adaptive Clearing (10% WOC) 4F 0.48 mm 9.52 mm 1.6608× 6,281 246.6 28.7 0.51

Shop-Floor Machining Strategy for 7075-T6 Aerospace Aluminum

Work Hardening: Low
Coolant & Lubrication Protocol

Flood Coolant with 8-10% Synthetic Soluble Oil Concentration

Pressure: Standard flood (5 bar minimum)

Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.

Chip Evacuation & Tool Path Guidance

Chip Flow: Excellent short crisp chips compared to 6061. Can run 3-flute tools at aggressive feeds.

Milling Direction: Climb milling gives mirror surface finishes.

Expert Machinist Tips:
  • High zinc content gives higher tensile strength; chips shear off crisply.
  • Maintain tool rigidity; deflection causes dimensional drift on tight aerospace tolerances.
  • Ideal candidate for High-Speed Machining (HSM) with high axial depth and light radial stepover.

Frequently Asked CNC Questions (7075-T6 Aerospace Aluminum / 3/16" (0.1875 in))

What is the recommended RPM for milling 7075-T6 Aerospace Aluminum with a 3/16" (0.1875 in) end mill?
For a 3/16" (0.1875 in) (4.762 mm) TiAlN coated carbide end mill in 7075-T6 Aerospace Aluminum, the baseline surface cutting speed is 580 m/min (1902.9 SFM), which translates to a calculated spindle speed of 38,769 RPM. If using uncoated carbide, reduce surface speed to 480 m/min (1600 SFM / 32085 RPM). For HSS cutters, speed must be restricted to 100 m/min (6684 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/16" (0.1875 in) in 7075-T6 Aerospace Aluminum?
At 38,769 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0282 mm/tooth (0.00111"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 3280 mm/min (129.1 IPM). Ramping or plunging into material should be limited to 35% of table feed (1148 mm/min / 45.2 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1.19 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 7075-T6 Aerospace Aluminum?
Flood Coolant with 8-10% Synthetic Soluble Oil Concentration. Pressure specification: Standard flood (5 bar minimum). Engineering rationale: Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.