7075-T6 Aerospace Aluminum — 12 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 7075-T6 Aerospace Aluminum with a 12 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 15,385 RPM at 580 m/min (1902.9 SFM), with a profiling feed rate of 1,815 mm/min (71.4 IPM) and adjusted chip load of 0.059 mm/tooth, achieving a material removal rate of 98.01 cm³/min (5.98 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math7075-T6 Aerospace Aluminum (12 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 12 mm | 6 mm | 1× | 1,178 | 46.5 | 84.82 | 1.5 |
| Slotting (100% WOC) | 3F | 12 mm | 6 mm | 1× | 1,768 | 69.7 | 127.3 | 2.25 |
| Slotting (100% WOC) | 4F | 12 mm | 6 mm | 1× | 2,357 | 92.9 | 169.7 | 3.01 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 3 mm | 18 mm | 1.1547× | 1,815 | 71.4 | 98.01 | 1.74 |
| Profiling / HEM (25% WOC) | 3F | 3 mm | 18 mm | 1.1547× | 2,723 | 107.1 | 147.04 | 2.6 |
| Profiling / HEM (25% WOC) | 4F | 3 mm | 18 mm | 1.1547× | 3,631 | 142.8 | 196.07 | 3.47 |
| Adaptive Clearing (10% WOC) | 2F | 1.2 mm | 24 mm | 1.6667× | 2,622 | 103.1 | 75.51 | 1.34 |
| Adaptive Clearing (10% WOC) | 3F | 1.2 mm | 24 mm | 1.6667× | 3,932 | 154.6 | 113.24 | 2.01 |
| Adaptive Clearing (10% WOC) | 4F | 1.2 mm | 24 mm | 1.6667× | 5,243 | 206.2 | 151 | 2.67 |
Shop-Floor Machining Strategy for 7075-T6 Aerospace Aluminum
Work Hardening: LowFlood Coolant with 8-10% Synthetic Soluble Oil Concentration
Pressure: Standard flood (5 bar minimum)
Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.
Chip Flow: Excellent short crisp chips compared to 6061. Can run 3-flute tools at aggressive feeds.
Milling Direction: Climb milling gives mirror surface finishes.
- High zinc content gives higher tensile strength; chips shear off crisply.
- Maintain tool rigidity; deflection causes dimensional drift on tight aerospace tolerances.
- Ideal candidate for High-Speed Machining (HSM) with high axial depth and light radial stepover.
Frequently Asked CNC Questions (7075-T6 Aerospace Aluminum / 12 mm)
What is the recommended RPM for milling 7075-T6 Aerospace Aluminum with a 12 mm end mill?
What table feed rate and chip load should I program for 12 mm in 7075-T6 Aerospace Aluminum?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 7075-T6 Aerospace Aluminum?
Recent Calculations
No recent calculations saved yet.