Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

7075-T6 Aerospace Aluminum — 12 mm 3-Flute Speeds & Feeds

ISO Group N 150 HB / 87 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
15,385 RPM
Surface Speed: 580 m/min (1902.9 SFM)
Table Feed Rate F = RPM·z·fz
2,723 mm/min
107.1 IPM
Plunge/Ramp Rate: 953 mm/min
Adjusted Chip Load CTF: 1.1547×
0.059 mm/t
0.00232 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
147.04 cm³/min
8.96 in³/min
Power Required: 2.6 kW (3.49 HP)
Direct CNC Machining Solution

For milling 7075-T6 Aerospace Aluminum with a 12 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 15,385 RPM at 580 m/min (1902.9 SFM), with a profiling feed rate of 2,723 mm/min (107.1 IPM) and adjusted chip load of 0.059 mm/tooth, achieving a material removal rate of 147.04 cm³/min (8.96 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
7075-T6 Aerospace Aluminum Stock CLIMB D = 12 mm (0.4724") ae = 3 mm ap = 18 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 1.29 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (580 × 1000) / (π × 12) = 15,385 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 3/12 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0511 mm × 1.1547 = 0.059 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 15,385 × 3 × 0.059 = 2,723 mm/min (107.1 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (18 × 3 × 2723) / 1000 = 147.04 cm³/min (8.96 in³/min)
Specific Cutting Force (kc) for 7075-T6 Aerospace Aluminum: 850 N/mm². Spindle drive efficiency η = 0.80.

7075-T6 Aerospace Aluminum (12 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 12 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 12 mm 6 mm 1× 1,178 46.5 84.82 1.5
Slotting (100% WOC) 3F 12 mm 6 mm 1× 1,768 69.7 127.3 2.25
Slotting (100% WOC) 4F 12 mm 6 mm 1× 2,357 92.9 169.7 3.01
Profiling / HEM (25% WOC) 2F 3 mm 18 mm 1.1547× 1,815 71.4 98.01 1.74
Profiling / HEM (25% WOC) CURRENT 3F 3 mm 18 mm 1.1547× 2,723 107.1 147.04 2.6
Profiling / HEM (25% WOC) 4F 3 mm 18 mm 1.1547× 3,631 142.8 196.07 3.47
Adaptive Clearing (10% WOC) 2F 1.2 mm 24 mm 1.6667× 2,622 103.1 75.51 1.34
Adaptive Clearing (10% WOC) 3F 1.2 mm 24 mm 1.6667× 3,932 154.6 113.24 2.01
Adaptive Clearing (10% WOC) 4F 1.2 mm 24 mm 1.6667× 5,243 206.2 151 2.67

Shop-Floor Machining Strategy for 7075-T6 Aerospace Aluminum

Work Hardening: Low
Coolant & Lubrication Protocol

Flood Coolant with 8-10% Synthetic Soluble Oil Concentration

Pressure: Standard flood (5 bar minimum)

Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.

Chip Evacuation & Tool Path Guidance

Chip Flow: Excellent short crisp chips compared to 6061. Can run 3-flute tools at aggressive feeds.

Milling Direction: Climb milling gives mirror surface finishes.

Expert Machinist Tips:
  • High zinc content gives higher tensile strength; chips shear off crisply.
  • Maintain tool rigidity; deflection causes dimensional drift on tight aerospace tolerances.
  • Ideal candidate for High-Speed Machining (HSM) with high axial depth and light radial stepover.

Frequently Asked CNC Questions (7075-T6 Aerospace Aluminum / 12 mm)

What is the recommended RPM for milling 7075-T6 Aerospace Aluminum with a 12 mm end mill?
For a 12 mm (12 mm) TiAlN coated carbide end mill in 7075-T6 Aerospace Aluminum, the baseline surface cutting speed is 580 m/min (1902.9 SFM), which translates to a calculated spindle speed of 15,385 RPM. If using uncoated carbide, reduce surface speed to 480 m/min (1600 SFM / 12732 RPM). For HSS cutters, speed must be restricted to 100 m/min (2653 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 12 mm in 7075-T6 Aerospace Aluminum?
At 15,385 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.059 mm/tooth (0.00232"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 2723 mm/min (107.1 IPM). Ramping or plunging into material should be limited to 35% of table feed (953 mm/min / 37.5 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 3 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 7075-T6 Aerospace Aluminum?
Flood Coolant with 8-10% Synthetic Soluble Oil Concentration. Pressure specification: Standard flood (5 bar minimum). Engineering rationale: Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.