Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

7075-T6 Aerospace Aluminum — 3/4" (0.750 in) 2-Flute Speeds & Feeds

ISO Group N 150 HB / 87 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
9,691 RPM
Surface Speed: 580 m/min (1902.9 SFM)
Table Feed Rate F = RPM·z·fz
1,657 mm/min
65.3 IPM
Plunge/Ramp Rate: 580 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0855 mm/t
0.00337 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
225.42 cm³/min
13.77 in³/min
Power Required: 3.99 kW (5.35 HP)
Direct CNC Machining Solution

For milling 7075-T6 Aerospace Aluminum with a 3/4" (0.750 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 9,691 RPM at 580 m/min (1902.9 SFM), with a profiling feed rate of 1,657 mm/min (65.3 IPM) and adjusted chip load of 0.0855 mm/tooth, achieving a material removal rate of 225.42 cm³/min (13.77 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
7075-T6 Aerospace Aluminum Stock CLIMB D = 19.05 mm (0.75") ae = 4.76 mm ap = 28.58 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 3.14 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (580 × 1000) / (π × 19.05) = 9,691 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 4.76/19.05 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.074 mm × 1.1549 = 0.0855 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 9,691 × 2 × 0.0855 = 1,657 mm/min (65.3 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (28.58 × 4.76 × 1657) / 1000 = 225.42 cm³/min (13.77 in³/min)
Specific Cutting Force (kc) for 7075-T6 Aerospace Aluminum: 850 N/mm². Spindle drive efficiency η = 0.80.

7075-T6 Aerospace Aluminum (3/4" (0.750 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/4" (0.750 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 19.05 mm 9.53 mm 1× 1,076 42.4 195.34 3.46
Slotting (100% WOC) 3F 19.05 mm 9.53 mm 1× 1,614 63.7 293.02 5.19
Slotting (100% WOC) 4F 19.05 mm 9.53 mm 1× 2,151 84.9 390.51 6.92
Profiling / HEM (25% WOC) CURRENT 2F 4.76 mm 28.58 mm 1.1549× 1,657 65.3 225.42 3.99
Profiling / HEM (25% WOC) 3F 4.76 mm 28.58 mm 1.1549× 2,486 98 338.2 5.99
Profiling / HEM (25% WOC) 4F 4.76 mm 28.58 mm 1.1549× 3,314 130.6 450.84 7.98
Adaptive Clearing (10% WOC) 2F 1.91 mm 38.1 mm 1.6647× 2,388 94 173.78 3.08
Adaptive Clearing (10% WOC) 3F 1.91 mm 38.1 mm 1.6647× 3,582 141 260.67 4.62
Adaptive Clearing (10% WOC) 4F 1.91 mm 38.1 mm 1.6647× 4,776 188 347.55 6.15

Shop-Floor Machining Strategy for 7075-T6 Aerospace Aluminum

Work Hardening: Low
Coolant & Lubrication Protocol

Flood Coolant with 8-10% Synthetic Soluble Oil Concentration

Pressure: Standard flood (5 bar minimum)

Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.

Chip Evacuation & Tool Path Guidance

Chip Flow: Excellent short crisp chips compared to 6061. Can run 3-flute tools at aggressive feeds.

Milling Direction: Climb milling gives mirror surface finishes.

Expert Machinist Tips:
  • High zinc content gives higher tensile strength; chips shear off crisply.
  • Maintain tool rigidity; deflection causes dimensional drift on tight aerospace tolerances.
  • Ideal candidate for High-Speed Machining (HSM) with high axial depth and light radial stepover.

Frequently Asked CNC Questions (7075-T6 Aerospace Aluminum / 3/4" (0.750 in))

What is the recommended RPM for milling 7075-T6 Aerospace Aluminum with a 3/4" (0.750 in) end mill?
For a 3/4" (0.750 in) (19.05 mm) TiAlN coated carbide end mill in 7075-T6 Aerospace Aluminum, the baseline surface cutting speed is 580 m/min (1902.9 SFM), which translates to a calculated spindle speed of 9,691 RPM. If using uncoated carbide, reduce surface speed to 480 m/min (1600 SFM / 8020 RPM). For HSS cutters, speed must be restricted to 100 m/min (1671 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/4" (0.750 in) in 7075-T6 Aerospace Aluminum?
At 9,691 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0855 mm/tooth (0.00337"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 1657 mm/min (65.3 IPM). Ramping or plunging into material should be limited to 35% of table feed (580 mm/min / 22.9 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 4.76 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 7075-T6 Aerospace Aluminum?
Flood Coolant with 8-10% Synthetic Soluble Oil Concentration. Pressure specification: Standard flood (5 bar minimum). Engineering rationale: Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.