Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

7075-T6 Aerospace Aluminum — 6 mm 3-Flute Speeds & Feeds

ISO Group N 150 HB / 87 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
30,770 RPM
Surface Speed: 580 m/min (1902.9 SFM)
Table Feed Rate F = RPM·z·fz
3,129 mm/min
122.8 IPM
Plunge/Ramp Rate: 1095 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0339 mm/t
0.00133 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
42.24 cm³/min
2.57 in³/min
Power Required: 0.75 kW (1 HP)
Direct CNC Machining Solution

For milling 7075-T6 Aerospace Aluminum with a 6 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 30,770 RPM at 580 m/min (1902.9 SFM), with a profiling feed rate of 3,129 mm/min (122.8 IPM) and adjusted chip load of 0.0339 mm/tooth, achieving a material removal rate of 42.24 cm³/min (2.57 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
7075-T6 Aerospace Aluminum Stock CLIMB D = 6 mm (0.2362") ae = 1.5 mm ap = 9 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.19 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (580 × 1000) / (π × 6) = 30,770 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1.5/6 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0294 mm × 1.1547 = 0.0339 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 30,770 × 3 × 0.0339 = 3,129 mm/min (122.8 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (9 × 1.5 × 3129) / 1000 = 42.24 cm³/min (2.57 in³/min)
Specific Cutting Force (kc) for 7075-T6 Aerospace Aluminum: 850 N/mm². Spindle drive efficiency η = 0.80.

7075-T6 Aerospace Aluminum (6 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 6 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 6 mm 3 mm 1× 1,354 53.5 24.37 0.43
Slotting (100% WOC) 3F 6 mm 3 mm 1× 2,031 80.3 36.56 0.65
Slotting (100% WOC) 4F 6 mm 3 mm 1× 2,708 107.1 48.74 0.86
Profiling / HEM (25% WOC) 2F 1.5 mm 9 mm 1.1547× 2,086 81.8 28.16 0.5
Profiling / HEM (25% WOC) CURRENT 3F 1.5 mm 9 mm 1.1547× 3,129 122.8 42.24 0.75
Profiling / HEM (25% WOC) 4F 1.5 mm 9 mm 1.1547× 4,172 163.7 56.32 1
Adaptive Clearing (10% WOC) 2F 0.6 mm 12 mm 1.6667× 3,015 118.8 21.71 0.38
Adaptive Clearing (10% WOC) 3F 0.6 mm 12 mm 1.6667× 4,523 178.2 32.57 0.58
Adaptive Clearing (10% WOC) 4F 0.6 mm 12 mm 1.6667× 6,031 237.5 43.42 0.77

Shop-Floor Machining Strategy for 7075-T6 Aerospace Aluminum

Work Hardening: Low
Coolant & Lubrication Protocol

Flood Coolant with 8-10% Synthetic Soluble Oil Concentration

Pressure: Standard flood (5 bar minimum)

Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.

Chip Evacuation & Tool Path Guidance

Chip Flow: Excellent short crisp chips compared to 6061. Can run 3-flute tools at aggressive feeds.

Milling Direction: Climb milling gives mirror surface finishes.

Expert Machinist Tips:
  • High zinc content gives higher tensile strength; chips shear off crisply.
  • Maintain tool rigidity; deflection causes dimensional drift on tight aerospace tolerances.
  • Ideal candidate for High-Speed Machining (HSM) with high axial depth and light radial stepover.

Frequently Asked CNC Questions (7075-T6 Aerospace Aluminum / 6 mm)

What is the recommended RPM for milling 7075-T6 Aerospace Aluminum with a 6 mm end mill?
For a 6 mm (6 mm) TiAlN coated carbide end mill in 7075-T6 Aerospace Aluminum, the baseline surface cutting speed is 580 m/min (1902.9 SFM), which translates to a calculated spindle speed of 30,770 RPM. If using uncoated carbide, reduce surface speed to 480 m/min (1600 SFM / 25465 RPM). For HSS cutters, speed must be restricted to 100 m/min (5305 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 6 mm in 7075-T6 Aerospace Aluminum?
At 30,770 RPM with a 3-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0339 mm/tooth (0.00133"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 3129 mm/min (122.8 IPM). Ramping or plunging into material should be limited to 35% of table feed (1095 mm/min / 43 IPM) at an entry ramp angle of 2.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1.5 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 7075-T6 Aerospace Aluminum?
Flood Coolant with 8-10% Synthetic Soluble Oil Concentration. Pressure specification: Standard flood (5 bar minimum). Engineering rationale: Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.