7075-T6 Aerospace Aluminum — 6 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 7075-T6 Aerospace Aluminum with a 6 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 30,770 RPM at 580 m/min (1902.9 SFM), with a profiling feed rate of 4,172 mm/min (163.7 IPM) and adjusted chip load of 0.0339 mm/tooth, achieving a material removal rate of 56.32 cm³/min (3.43 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math7075-T6 Aerospace Aluminum (6 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6 mm | 3 mm | 1× | 1,354 | 53.5 | 24.37 | 0.43 |
| Slotting (100% WOC) | 3F | 6 mm | 3 mm | 1× | 2,031 | 80.3 | 36.56 | 0.65 |
| Slotting (100% WOC) | 4F | 6 mm | 3 mm | 1× | 2,708 | 107.1 | 48.74 | 0.86 |
| Profiling / HEM (25% WOC) | 2F | 1.5 mm | 9 mm | 1.1547× | 2,086 | 81.8 | 28.16 | 0.5 |
| Profiling / HEM (25% WOC) | 3F | 1.5 mm | 9 mm | 1.1547× | 3,129 | 122.8 | 42.24 | 0.75 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 1.5 mm | 9 mm | 1.1547× | 4,172 | 163.7 | 56.32 | 1 |
| Adaptive Clearing (10% WOC) | 2F | 0.6 mm | 12 mm | 1.6667× | 3,015 | 118.8 | 21.71 | 0.38 |
| Adaptive Clearing (10% WOC) | 3F | 0.6 mm | 12 mm | 1.6667× | 4,523 | 178.2 | 32.57 | 0.58 |
| Adaptive Clearing (10% WOC) | 4F | 0.6 mm | 12 mm | 1.6667× | 6,031 | 237.5 | 43.42 | 0.77 |
Shop-Floor Machining Strategy for 7075-T6 Aerospace Aluminum
Work Hardening: LowFlood Coolant with 8-10% Synthetic Soluble Oil Concentration
Pressure: Standard flood (5 bar minimum)
Zinc-alloyed aluminum chips break cleaner than 6061, with superior surface finish.
Chip Flow: Excellent short crisp chips compared to 6061. Can run 3-flute tools at aggressive feeds.
Milling Direction: Climb milling gives mirror surface finishes.
- High zinc content gives higher tensile strength; chips shear off crisply.
- Maintain tool rigidity; deflection causes dimensional drift on tight aerospace tolerances.
- Ideal candidate for High-Speed Machining (HSM) with high axial depth and light radial stepover.
Frequently Asked CNC Questions (7075-T6 Aerospace Aluminum / 6 mm)
What is the recommended RPM for milling 7075-T6 Aerospace Aluminum with a 6 mm end mill?
What table feed rate and chip load should I program for 6 mm in 7075-T6 Aerospace Aluminum?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 7075-T6 Aerospace Aluminum?
Recent Calculations
No recent calculations saved yet.