C11000 Electrolytic Tough Pitch (ETP) Copper — 1/2" (0.500 in) 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 1/2" (0.500 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 6,266 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 498 mm/min (19.5 IPM) and adjusted chip load of 0.0397 mm/tooth, achieving a material removal rate of 30.07 cm³/min (1.83 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathC11000 Electrolytic Tough Pitch (ETP) Copper (1/2" (0.500 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 12.7 mm | 6.35 mm | 1× | 323 | 12.8 | 26.05 | 0.6 |
| Slotting (100% WOC) | 3F | 12.7 mm | 6.35 mm | 1× | 485 | 19.2 | 39.11 | 0.9 |
| Slotting (100% WOC) | 4F | 12.7 mm | 6.35 mm | 1× | 647 | 25.6 | 52.18 | 1.2 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 3.17 mm | 19.05 mm | 1.1553× | 498 | 19.5 | 30.07 | 0.69 |
| Profiling / HEM (25% WOC) | 3F | 3.17 mm | 19.05 mm | 1.1553× | 746 | 29.3 | 45.05 | 1.03 |
| Profiling / HEM (25% WOC) | 4F | 3.17 mm | 19.05 mm | 1.1553× | 995 | 39.1 | 60.09 | 1.38 |
| Adaptive Clearing (10% WOC) | 2F | 1.27 mm | 25.4 mm | 1.6667× | 718 | 28.3 | 23.16 | 0.53 |
| Adaptive Clearing (10% WOC) | 3F | 1.27 mm | 25.4 mm | 1.6667× | 1,077 | 42.5 | 34.74 | 0.8 |
| Adaptive Clearing (10% WOC) | 4F | 1.27 mm | 25.4 mm | 1.6667× | 1,436 | 56.6 | 46.32 | 1.06 |
Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper
Work Hardening: ModerateAbundant Flood Coolant with High Lubricity Emulsion or Mineral Oil
Pressure: Flood at 8 bar minimum
Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.
Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.
Milling Direction: Climb milling with high positive rake angles.
- Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
- Keep feed rate positive to shear rather than plow or smear the copper grain structure.
- Program chamfering passes immediately following roughing before secondary operations.
Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 1/2" (0.500 in))
What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 1/2" (0.500 in) end mill?
What table feed rate and chip load should I program for 1/2" (0.500 in) in C11000 Electrolytic Tough Pitch (ETP) Copper?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Recent Calculations
No recent calculations saved yet.