Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

6061-T6 Aluminum — 1/2" (0.500 in) 2-Flute Speeds & Feeds

ISO Group N 95 HB (Brinell) / 60 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
16,291 RPM
Surface Speed: 650 m/min (2132.5 SFM)
Table Feed Rate F = RPM·z·fz
2,157 mm/min
85 IPM
Plunge/Ramp Rate: 755 mm/min
Adjusted Chip Load CTF: 1.1553×
0.0662 mm/t
0.00261 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
130.26 cm³/min
7.96 in³/min
Power Required: 1.9 kW (2.55 HP)
Direct CNC Machining Solution

For milling 6061-T6 Aluminum with a 1/2" (0.500 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 16,291 RPM at 650 m/min (2132.5 SFM), with a profiling feed rate of 2,157 mm/min (85 IPM) and adjusted chip load of 0.0662 mm/tooth, achieving a material removal rate of 130.26 cm³/min (7.96 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
6061-T6 Aluminum Stock CLIMB D = 12.7 mm (0.5") ae = 3.17 mm ap = 19.05 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1553×
Spindle Torque 0.89 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (650 × 1000) / (π × 12.7) = 16,291 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 3.17/12.7 = 0.25 → CTF = 1.1553×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0573 mm × 1.1553 = 0.0662 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 16,291 × 2 × 0.0662 = 2,157 mm/min (85 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (19.05 × 3.17 × 2157) / 1000 = 130.26 cm³/min (7.96 in³/min)
Specific Cutting Force (kc) for 6061-T6 Aluminum: 700 N/mm². Spindle drive efficiency η = 0.80.

6061-T6 Aluminum (1/2" (0.500 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1/2" (0.500 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 12.7 mm 6.35 mm 1× 1,401 55.1 112.98 1.65
Slotting (100% WOC) 3F 12.7 mm 6.35 mm 1× 2,102 82.6 169.52 2.47
Slotting (100% WOC) 4F 12.7 mm 6.35 mm 1× 2,802 110.1 225.97 3.3
Profiling / HEM (25% WOC) CURRENT 2F 3.17 mm 19.05 mm 1.1553× 2,157 85 130.26 1.9
Profiling / HEM (25% WOC) 3F 3.17 mm 19.05 mm 1.1553× 3,235 127.6 195.36 2.85
Profiling / HEM (25% WOC) 4F 3.17 mm 19.05 mm 1.1553× 4,314 170.1 260.52 3.8
Adaptive Clearing (10% WOC) 2F 1.27 mm 25.4 mm 1.6667× 3,112 122.5 100.39 1.46
Adaptive Clearing (10% WOC) 3F 1.27 mm 25.4 mm 1.6667× 4,667 183.8 150.55 2.2
Adaptive Clearing (10% WOC) 4F 1.27 mm 25.4 mm 1.6667× 6,223 245 200.74 2.93

Shop-Floor Machining Strategy for 6061-T6 Aluminum

Work Hardening: Low
Coolant & Lubrication Protocol

High-Pressure Flood Coolant or MQL Air Blast with Alcohol/Oil Mist

Pressure: Flood at 5-10 bar; Through-Spindle 20 bar

Lubricity is critical. Dry cutting risks instantaneous aluminum welding to tool flutes and catastrophic cutter snap.

Chip Evacuation & Tool Path Guidance

Chip Flow: Use polished flutes (ZrN or DLC coating) and 2 or 3 flutes to prevent chip re-cutting.

Milling Direction: Always climb mill. Conventional milling causes built-up edge on the tool face.

Expert Machinist Tips:
  • Max spindle speed is usually preferred; feed fast to maintain minimum chip thickness (>0.02 mm) to prevent rubbing.
  • In deep pocketing, utilize high pressure air blast to blast chips out of the cavity.
  • For high-speed trochoidal slotting, use 10-15% radial stepover (ae) at 2.0x-3.0x axial depth (ap).

Frequently Asked CNC Questions (6061-T6 Aluminum / 1/2" (0.500 in))

What is the recommended RPM for milling 6061-T6 Aluminum with a 1/2" (0.500 in) end mill?
For a 1/2" (0.500 in) (12.7 mm) TiAlN coated carbide end mill in 6061-T6 Aluminum, the baseline surface cutting speed is 650 m/min (2132.5 SFM), which translates to a calculated spindle speed of 16,291 RPM. If using uncoated carbide, reduce surface speed to 550 m/min (1800 SFM / 13785 RPM). For HSS cutters, speed must be restricted to 120 m/min (3008 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1/2" (0.500 in) in 6061-T6 Aluminum?
At 16,291 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0662 mm/tooth (0.00261"/tooth) after applying a radial chip thinning factor (CTF) of 1.1553×. This yields a table feed rate of 2157 mm/min (85 IPM). Ramping or plunging into material should be limited to 35% of table feed (755 mm/min / 29.7 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 3.17 mm), the Chip Thinning Factor is 1.1553×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 6061-T6 Aluminum?
High-Pressure Flood Coolant or MQL Air Blast with Alcohol/Oil Mist. Pressure specification: Flood at 5-10 bar; Through-Spindle 20 bar. Engineering rationale: Lubricity is critical. Dry cutting risks instantaneous aluminum welding to tool flutes and catastrophic cutter snap.