C11000 Electrolytic Tough Pitch (ETP) Copper — 16 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 16 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 4,974 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 476 mm/min (18.7 IPM) and adjusted chip load of 0.0478 mm/tooth, achieving a material removal rate of 45.7 cm³/min (2.78 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathC11000 Electrolytic Tough Pitch (ETP) Copper (16 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 16 mm | 8 mm | 1× | 308 | 12.1 | 39.42 | 0.9 |
| Slotting (100% WOC) | 3F | 16 mm | 8 mm | 1× | 463 | 18.2 | 59.26 | 1.36 |
| Slotting (100% WOC) | 4F | 16 mm | 8 mm | 1× | 617 | 24.3 | 78.98 | 1.81 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 4 mm | 24 mm | 1.1547× | 476 | 18.7 | 45.7 | 1.05 |
| Profiling / HEM (25% WOC) | 3F | 4 mm | 24 mm | 1.1547× | 713 | 28.1 | 68.45 | 1.57 |
| Profiling / HEM (25% WOC) | 4F | 4 mm | 24 mm | 1.1547× | 951 | 37.4 | 91.3 | 2.09 |
| Adaptive Clearing (10% WOC) | 2F | 1.6 mm | 32 mm | 1.6667× | 686 | 27.1 | 35.12 | 0.8 |
| Adaptive Clearing (10% WOC) | 3F | 1.6 mm | 32 mm | 1.6667× | 1,030 | 40.6 | 52.74 | 1.21 |
| Adaptive Clearing (10% WOC) | 4F | 1.6 mm | 32 mm | 1.6667× | 1,373 | 54.1 | 70.3 | 1.61 |
Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper
Work Hardening: ModerateAbundant Flood Coolant with High Lubricity Emulsion or Mineral Oil
Pressure: Flood at 8 bar minimum
Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.
Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.
Milling Direction: Climb milling with high positive rake angles.
- Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
- Keep feed rate positive to shear rather than plow or smear the copper grain structure.
- Program chamfering passes immediately following roughing before secondary operations.
Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 16 mm)
What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 16 mm end mill?
What table feed rate and chip load should I program for 16 mm in C11000 Electrolytic Tough Pitch (ETP) Copper?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Recent Calculations
No recent calculations saved yet.