C11000 Electrolytic Tough Pitch (ETP) Copper — 2 mm 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 2 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 39,789 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 716 mm/min (27.9 IPM) and adjusted chip load of 0.009 mm/tooth, achieving a material removal rate of 1.07 cm³/min (0.06 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathC11000 Electrolytic Tough Pitch (ETP) Copper (2 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 2 mm | 1 mm | 1× | 470 | 18.3 | 0.94 | 0.02 |
| Slotting (100% WOC) | 3F | 2 mm | 1 mm | 1× | 704 | 27.5 | 1.41 | 0.03 |
| Slotting (100% WOC) | 4F | 2 mm | 1 mm | 1× | 939 | 36.6 | 1.88 | 0.04 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 0.5 mm | 3 mm | 1.1547× | 716 | 27.9 | 1.07 | 0.02 |
| Profiling / HEM (25% WOC) | 3F | 0.5 mm | 3 mm | 1.1547× | 1,074 | 41.8 | 1.61 | 0.04 |
| Profiling / HEM (25% WOC) | 4F | 0.5 mm | 3 mm | 1.1547× | 1,432 | 55.7 | 2.15 | 0.05 |
| Adaptive Clearing (10% WOC) | 2F | 0.2 mm | 4 mm | 1.6667× | 1,035 | 40.6 | 0.83 | 0.02 |
| Adaptive Clearing (10% WOC) | 3F | 0.2 mm | 4 mm | 1.6667× | 1,552 | 60.9 | 1.24 | 0.03 |
| Adaptive Clearing (10% WOC) | 4F | 0.2 mm | 4 mm | 1.6667× | 2,069 | 81.2 | 1.66 | 0.04 |
Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper
Work Hardening: ModerateAbundant Flood Coolant with High Lubricity Emulsion or Mineral Oil
Pressure: Flood at 8 bar minimum
Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.
Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.
Milling Direction: Climb milling with high positive rake angles.
- Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
- Keep feed rate positive to shear rather than plow or smear the copper grain structure.
- Program chamfering passes immediately following roughing before secondary operations.
Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 2 mm)
What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 2 mm end mill?
What table feed rate and chip load should I program for 2 mm in C11000 Electrolytic Tough Pitch (ETP) Copper?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Recent Calculations
No recent calculations saved yet.