Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

6061-T6 Aluminum — 2 mm 2-Flute Speeds & Feeds

ISO Group N 95 HB (Brinell) / 60 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
1,03,451 RPM
Surface Speed: 650 m/min (2132.5 SFM)
Table Feed Rate F = RPM·z·fz
3,124 mm/min
122.1 IPM
Plunge/Ramp Rate: 1093 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0151 mm/t
0.00059 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
4.69 cm³/min
0.28 in³/min
Power Required: 0.07 kW (0.09 HP)
Direct CNC Machining Solution

For milling 6061-T6 Aluminum with a 2 mm 2-flute TiAlN carbide end mill, the recommended spindle speed is 1,03,451 RPM at 650 m/min (2132.5 SFM), with a profiling feed rate of 3,124 mm/min (122.1 IPM) and adjusted chip load of 0.0151 mm/tooth, achieving a material removal rate of 4.69 cm³/min (0.28 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
6061-T6 Aluminum Stock CLIMB D = 2 mm (0.0787") ae = 0.5 mm ap = 3 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (650 × 1000) / (π × 2) = 1,03,451 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.5/2 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0131 mm × 1.1547 = 0.0151 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 1,03,451 × 2 × 0.0151 = 3,124 mm/min (122.1 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (3 × 0.5 × 3124) / 1000 = 4.69 cm³/min (0.28 in³/min)
Specific Cutting Force (kc) for 6061-T6 Aluminum: 700 N/mm². Spindle drive efficiency η = 0.80.

6061-T6 Aluminum (2 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 2 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 2 mm 1 mm 1× 2,028 80.7 4.06 0.06
Slotting (100% WOC) 3F 2 mm 1 mm 1× 3,041 121 6.08 0.09
Slotting (100% WOC) 4F 2 mm 1 mm 1× 4,055 161.4 8.11 0.12
Profiling / HEM (25% WOC) CURRENT 2F 0.5 mm 3 mm 1.1547× 3,124 122.1 4.69 0.07
Profiling / HEM (25% WOC) 3F 0.5 mm 3 mm 1.1547× 4,686 183.1 7.03 0.1
Profiling / HEM (25% WOC) 4F 0.5 mm 3 mm 1.1547× 6,248 244.1 9.37 0.14
Adaptive Clearing (10% WOC) 2F 0.2 mm 4 mm 1.6667× 4,510 177.9 3.61 0.05
Adaptive Clearing (10% WOC) 3F 0.2 mm 4 mm 1.6667× 6,766 266.9 5.41 0.08
Adaptive Clearing (10% WOC) 4F 0.2 mm 4 mm 1.6667× 9,021 355.9 7.22 0.11

Shop-Floor Machining Strategy for 6061-T6 Aluminum

Work Hardening: Low
Coolant & Lubrication Protocol

High-Pressure Flood Coolant or MQL Air Blast with Alcohol/Oil Mist

Pressure: Flood at 5-10 bar; Through-Spindle 20 bar

Lubricity is critical. Dry cutting risks instantaneous aluminum welding to tool flutes and catastrophic cutter snap.

Chip Evacuation & Tool Path Guidance

Chip Flow: Use polished flutes (ZrN or DLC coating) and 2 or 3 flutes to prevent chip re-cutting.

Milling Direction: Always climb mill. Conventional milling causes built-up edge on the tool face.

Expert Machinist Tips:
  • Max spindle speed is usually preferred; feed fast to maintain minimum chip thickness (>0.02 mm) to prevent rubbing.
  • In deep pocketing, utilize high pressure air blast to blast chips out of the cavity.
  • For high-speed trochoidal slotting, use 10-15% radial stepover (ae) at 2.0x-3.0x axial depth (ap).

Frequently Asked CNC Questions (6061-T6 Aluminum / 2 mm)

What is the recommended RPM for milling 6061-T6 Aluminum with a 2 mm end mill?
For a 2 mm (2 mm) TiAlN coated carbide end mill in 6061-T6 Aluminum, the baseline surface cutting speed is 650 m/min (2132.5 SFM), which translates to a calculated spindle speed of 1,03,451 RPM. If using uncoated carbide, reduce surface speed to 550 m/min (1800 SFM / 87535 RPM). For HSS cutters, speed must be restricted to 120 m/min (19099 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 2 mm in 6061-T6 Aluminum?
At 1,03,451 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0151 mm/tooth (0.00059"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 3124 mm/min (122.1 IPM). Ramping or plunging into material should be limited to 35% of table feed (1093 mm/min / 42.7 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.5 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 6061-T6 Aluminum?
High-Pressure Flood Coolant or MQL Air Blast with Alcohol/Oil Mist. Pressure specification: Flood at 5-10 bar; Through-Spindle 20 bar. Engineering rationale: Lubricity is critical. Dry cutting risks instantaneous aluminum welding to tool flutes and catastrophic cutter snap.