C11000 Electrolytic Tough Pitch (ETP) Copper — 4 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 4 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 19,894 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 1,249 mm/min (49.3 IPM) and adjusted chip load of 0.0157 mm/tooth, achieving a material removal rate of 7.49 cm³/min (0.46 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathC11000 Electrolytic Tough Pitch (ETP) Copper (4 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 4 mm | 2 mm | 1× | 406 | 15.9 | 3.25 | 0.07 |
| Slotting (100% WOC) | 3F | 4 mm | 2 mm | 1× | 609 | 23.9 | 4.87 | 0.11 |
| Slotting (100% WOC) | 4F | 4 mm | 2 mm | 1× | 812 | 31.8 | 6.5 | 0.15 |
| Profiling / HEM (25% WOC) | 2F | 1 mm | 6 mm | 1.1547× | 625 | 24.7 | 3.75 | 0.09 |
| Profiling / HEM (25% WOC) | 3F | 1 mm | 6 mm | 1.1547× | 937 | 37 | 5.62 | 0.13 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 1 mm | 6 mm | 1.1547× | 1,249 | 49.3 | 7.49 | 0.17 |
| Adaptive Clearing (10% WOC) | 2F | 0.4 mm | 8 mm | 1.6667× | 903 | 35.4 | 2.89 | 0.07 |
| Adaptive Clearing (10% WOC) | 3F | 0.4 mm | 8 mm | 1.6667× | 1,355 | 53.1 | 4.34 | 0.1 |
| Adaptive Clearing (10% WOC) | 4F | 0.4 mm | 8 mm | 1.6667× | 1,806 | 70.8 | 5.78 | 0.13 |
Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper
Work Hardening: ModerateAbundant Flood Coolant with High Lubricity Emulsion or Mineral Oil
Pressure: Flood at 8 bar minimum
Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.
Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.
Milling Direction: Climb milling with high positive rake angles.
- Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
- Keep feed rate positive to shear rather than plow or smear the copper grain structure.
- Program chamfering passes immediately following roughing before secondary operations.
Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 4 mm)
What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 4 mm end mill?
What table feed rate and chip load should I program for 4 mm in C11000 Electrolytic Tough Pitch (ETP) Copper?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Recent Calculations
No recent calculations saved yet.