C11000 Electrolytic Tough Pitch (ETP) Copper — 6 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 6 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 13,263 RPM at 250 m/min (820.2 SFM), with a profiling feed rate of 1,157 mm/min (45.6 IPM) and adjusted chip load of 0.0218 mm/tooth, achieving a material removal rate of 15.62 cm³/min (0.95 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathC11000 Electrolytic Tough Pitch (ETP) Copper (6 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6 mm | 3 mm | 1× | 377 | 14.9 | 6.79 | 0.16 |
| Slotting (100% WOC) | 3F | 6 mm | 3 mm | 1× | 565 | 22.3 | 10.17 | 0.23 |
| Slotting (100% WOC) | 4F | 6 mm | 3 mm | 1× | 753 | 29.7 | 13.55 | 0.31 |
| Profiling / HEM (25% WOC) | 2F | 1.5 mm | 9 mm | 1.1547× | 578 | 22.8 | 7.8 | 0.18 |
| Profiling / HEM (25% WOC) | 3F | 1.5 mm | 9 mm | 1.1547× | 867 | 34.2 | 11.7 | 0.27 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 1.5 mm | 9 mm | 1.1547× | 1,157 | 45.6 | 15.62 | 0.36 |
| Adaptive Clearing (10% WOC) | 2F | 0.6 mm | 12 mm | 1.6667× | 836 | 32.9 | 6.02 | 0.14 |
| Adaptive Clearing (10% WOC) | 3F | 0.6 mm | 12 mm | 1.6667× | 1,253 | 49.3 | 9.02 | 0.21 |
| Adaptive Clearing (10% WOC) | 4F | 0.6 mm | 12 mm | 1.6667× | 1,671 | 65.8 | 12.03 | 0.28 |
Shop-Floor Machining Strategy for C11000 Electrolytic Tough Pitch (ETP) Copper
Work Hardening: ModerateAbundant Flood Coolant with High Lubricity Emulsion or Mineral Oil
Pressure: Flood at 8 bar minimum
Pure copper is notoriously gummy; lubrication is mandatory to prevent cold welding to cutter flutes.
Chip Flow: Long, ductile continuous ribbons. Large 1-flute or 2-flute mirror-polished end mills are required.
Milling Direction: Climb milling with high positive rake angles.
- Use polished uncoated carbide designed for aluminum/non-ferrous; razor sharp cutting edges are mandatory.
- Keep feed rate positive to shear rather than plow or smear the copper grain structure.
- Program chamfering passes immediately following roughing before secondary operations.
Frequently Asked CNC Questions (C11000 Electrolytic Tough Pitch (ETP) Copper / 6 mm)
What is the recommended RPM for milling C11000 Electrolytic Tough Pitch (ETP) Copper with a 6 mm end mill?
What table feed rate and chip load should I program for 6 mm in C11000 Electrolytic Tough Pitch (ETP) Copper?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining C11000 Electrolytic Tough Pitch (ETP) Copper?
Recent Calculations
No recent calculations saved yet.