Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

C36000 Free-Cutting Brass — 5/8" (0.625 in) 4-Flute Speeds & Feeds

ISO Group N 120 HB / 78 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
8,421 RPM
Surface Speed: 420 m/min (1378 SFM)
Table Feed Rate F = RPM·z·fz
2,311 mm/min
90.9 IPM
Plunge/Ramp Rate: 809 mm/min
Adjusted Chip Load CTF: 1.1546×
0.0686 mm/t
0.0027 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
218.45 cm³/min
13.32 in³/min
Power Required: 3.41 kW (4.58 HP)
Direct CNC Machining Solution

For milling C36000 Free-Cutting Brass with a 5/8" (0.625 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 8,421 RPM at 420 m/min (1378 SFM), with a profiling feed rate of 2,311 mm/min (90.9 IPM) and adjusted chip load of 0.0686 mm/tooth, achieving a material removal rate of 218.45 cm³/min (13.32 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
C36000 Free-Cutting Brass Stock CLIMB D = 15.875 mm (0.625") ae = 3.97 mm ap = 23.81 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1546×
Spindle Torque 3.1 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (420 × 1000) / (π × 15.875) = 8,421 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 3.97/15.875 = 0.25 → CTF = 1.1546×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0594 mm × 1.1546 = 0.0686 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 8,421 × 4 × 0.0686 = 2,311 mm/min (90.9 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (23.81 × 3.97 × 2311) / 1000 = 218.45 cm³/min (13.32 in³/min)
Specific Cutting Force (kc) for C36000 Free-Cutting Brass: 750 N/mm². Spindle drive efficiency η = 0.80.

C36000 Free-Cutting Brass (5/8" (0.625 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 5/8" (0.625 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 15.88 mm 7.94 mm 1× 749 29.5 94.44 1.48
Slotting (100% WOC) 3F 15.88 mm 7.94 mm 1× 1,124 44.2 141.72 2.21
Slotting (100% WOC) 4F 15.88 mm 7.94 mm 1× 1,499 58.9 189 2.95
Profiling / HEM (25% WOC) 2F 3.97 mm 23.81 mm 1.1546× 1,155 45.5 109.18 1.71
Profiling / HEM (25% WOC) 3F 3.97 mm 23.81 mm 1.1546× 1,733 68.2 163.81 2.56
Profiling / HEM (25% WOC) CURRENT 4F 3.97 mm 23.81 mm 1.1546× 2,311 90.9 218.45 3.41
Adaptive Clearing (10% WOC) 2F 1.59 mm 31.75 mm 1.6655× 1,666 65.5 84.1 1.31
Adaptive Clearing (10% WOC) 3F 1.59 mm 31.75 mm 1.6655× 2,499 98.3 126.16 1.97
Adaptive Clearing (10% WOC) 4F 1.59 mm 31.75 mm 1.6655× 3,331 131 168.16 2.63

Shop-Floor Machining Strategy for C36000 Free-Cutting Brass

Work Hardening: Very Low
Coolant & Lubrication Protocol

Dry with Air Blast or Light Soluble Flood Coolant

Pressure: Air blast at 4-6 bar

Machines exceptionally well dry; lead micro-particles act as internal solid lubricant.

Chip Evacuation & Tool Path Guidance

Chip Flow: Produces broken powdery needle chips. Air blast keeps work area clear.

Milling Direction: Both climb and conventional work, but climb produces superior Ra finish.

Expert Machinist Tips:
  • Zero rake angle or slightly positive rake tooling prevents cutter self-feeding/grabbing into the material.
  • Spindle speeds can be maxed out on modern CNC centers.
  • Clean chip trays frequently as needle brass chips can clog sump pumps.

Frequently Asked CNC Questions (C36000 Free-Cutting Brass / 5/8" (0.625 in))

What is the recommended RPM for milling C36000 Free-Cutting Brass with a 5/8" (0.625 in) end mill?
For a 5/8" (0.625 in) (15.875 mm) TiAlN coated carbide end mill in C36000 Free-Cutting Brass, the baseline surface cutting speed is 420 m/min (1378 SFM), which translates to a calculated spindle speed of 8,421 RPM. If using uncoated carbide, reduce surface speed to 350 m/min (1150 SFM / 7018 RPM). For HSS cutters, speed must be restricted to 90 m/min (1805 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 5/8" (0.625 in) in C36000 Free-Cutting Brass?
At 8,421 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0686 mm/tooth (0.0027"/tooth) after applying a radial chip thinning factor (CTF) of 1.1546×. This yields a table feed rate of 2311 mm/min (90.9 IPM). Ramping or plunging into material should be limited to 35% of table feed (809 mm/min / 31.8 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 3.97 mm), the Chip Thinning Factor is 1.1546×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining C36000 Free-Cutting Brass?
Dry with Air Blast or Light Soluble Flood Coolant. Pressure specification: Air blast at 4-6 bar. Engineering rationale: Machines exceptionally well dry; lead micro-particles act as internal solid lubricant.