Carbon Fiber Reinforced Polymer (CFRP Composite) — 6 mm 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Carbon Fiber Reinforced Polymer (CFRP Composite) with a 6 mm 3-flute TiAlN carbide end mill, the recommended spindle speed is 10,080 RPM at 190 m/min (623.4 SFM), with a profiling feed rate of 514 mm/min (20.3 IPM) and adjusted chip load of 0.017 mm/tooth, achieving a material removal rate of 6.94 cm³/min (0.43 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathCarbon Fiber Reinforced Polymer (CFRP Composite) (6 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6 mm | 3 mm | 1× | 222 | 8.7 | 4 | 0.07 |
| Slotting (100% WOC) | 3F | 6 mm | 3 mm | 1× | 333 | 13 | 5.99 | 0.1 |
| Slotting (100% WOC) | 4F | 6 mm | 3 mm | 1× | 444 | 17.3 | 7.99 | 0.13 |
| Profiling / HEM (25% WOC) | 2F | 1.5 mm | 9 mm | 1.1547× | 343 | 13.5 | 4.63 | 0.08 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 1.5 mm | 9 mm | 1.1547× | 514 | 20.3 | 6.94 | 0.12 |
| Profiling / HEM (25% WOC) | 4F | 1.5 mm | 9 mm | 1.1547× | 685 | 27 | 9.25 | 0.15 |
| Adaptive Clearing (10% WOC) | 2F | 0.6 mm | 12 mm | 1.6667× | 494 | 19.4 | 3.56 | 0.06 |
| Adaptive Clearing (10% WOC) | 3F | 0.6 mm | 12 mm | 1.6667× | 741 | 29 | 5.34 | 0.09 |
| Adaptive Clearing (10% WOC) | 4F | 0.6 mm | 12 mm | 1.6667× | 988 | 38.7 | 7.11 | 0.12 |
Shop-Floor Machining Strategy for Carbon Fiber Reinforced Polymer (CFRP Composite)
Work Hardening: Severe abrasive flank wear; abrasive carbon fibers act like grinding grit.Dry with High-Velocity HEPA Downdraft Dust Collection or DI Water Flood
Pressure: HEPA vacuum pickup nozzle positioned directly at tool tip
WARNING: Airborne carbon dust is electrically conductive (destroys CNC electronics) and an inhalation health hazard. Standard coolant creates a sludge that must be specialty filtered.
Chip Flow: Carbon fiber does not form chips; it fractures into abrasive micro-powder.
Milling Direction: Compression style (upcut/downcut burr-style) tooling prevents top/bottom ply delamination.
- Use PCD (polycrystalline diamond) or thick CVD diamond-coated compression router bits.
- Compression geometry forces top plies downward and bottom plies upward into the part core, eliminating delamination.
- Inspect cutting edges frequently; worn cutters will tear and push fibers rather than shearing them cleanly.
Frequently Asked CNC Questions (Carbon Fiber Reinforced Polymer (CFRP Composite) / 6 mm)
What is the recommended RPM for milling Carbon Fiber Reinforced Polymer (CFRP Composite) with a 6 mm end mill?
What table feed rate and chip load should I program for 6 mm in Carbon Fiber Reinforced Polymer (CFRP Composite)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Carbon Fiber Reinforced Polymer (CFRP Composite)?
Recent Calculations
No recent calculations saved yet.