Delrin (Acetal / Polyoxymethylene / POM-C) — 1/4" (0.250 in) 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 1/4" (0.250 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 25,064 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 4,311 mm/min (169.4 IPM) and adjusted chip load of 0.043 mm/tooth, achieving a material removal rate of 65.25 cm³/min (3.97 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathDelrin (Acetal / Polyoxymethylene / POM-C) (1/4" (0.250 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 6.35 mm | 3.17 mm | 1× | 1,404 | 55.1 | 28.26 | 0.15 |
| Slotting (100% WOC) | 3F | 6.35 mm | 3.17 mm | 1× | 2,105 | 82.7 | 42.37 | 0.22 |
| Slotting (100% WOC) | 4F | 6.35 mm | 3.17 mm | 1× | 2,807 | 110.3 | 56.5 | 0.29 |
| Profiling / HEM (25% WOC) | 2F | 1.59 mm | 9.52 mm | 1.1541× | 2,156 | 84.7 | 32.63 | 0.17 |
| Profiling / HEM (25% WOC) | 3F | 1.59 mm | 9.52 mm | 1.1541× | 3,233 | 127.1 | 48.94 | 0.25 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 1.59 mm | 9.52 mm | 1.1541× | 4,311 | 169.4 | 65.25 | 0.34 |
| Adaptive Clearing (10% WOC) | 2F | 0.64 mm | 12.7 mm | 1.6609× | 3,108 | 122.3 | 25.26 | 0.13 |
| Adaptive Clearing (10% WOC) | 3F | 0.64 mm | 12.7 mm | 1.6609× | 4,662 | 183.5 | 37.89 | 0.2 |
| Adaptive Clearing (10% WOC) | 4F | 0.64 mm | 12.7 mm | 1.6609× | 6,216 | 244.6 | 50.52 | 0.26 |
Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)
Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant
Pressure: Air gun at 5 bar
Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.
Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.
Milling Direction: Climb milling produces pristine finishes.
- High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
- Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
- Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.
Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 1/4" (0.250 in))
What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 1/4" (0.250 in) end mill?
What table feed rate and chip load should I program for 1/4" (0.250 in) in Delrin (Acetal / Polyoxymethylene / POM-C)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Recent Calculations
No recent calculations saved yet.